EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31512 - Instructions

All Instructions for the 31512
16 - 30 of 35

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The old water assembly valve split on the bottom and started leaking.
4 of 6 people found this instruction helpful.
  • Jerry from CARYVILLE, TN
  • Very Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After unplugging the washer I cut the water off. I took the water hoses off, then the back top panel using a phillips head screw driver. I then used a pair of pliers to take off the two hoses and clamps. I unplugged the electric connection on each solenoid, took out 5 screws replaced the part and did everything in reverse order. Problem s olved. Thanks for the fast service on my order.
Was this helpful?
Thank you for voting!
I had no problems
3 of 4 people found this instruction helpful.
  • Sharron from RICHMOND, TX
  • Really Easy
  • 30 - 60 mins
  • Socket set, Wrench set
I can’t really say it was easy and I just did it
Was this helpful?
Thank you for voting!
washer making noise when washing. rinse and spin was normal.
2 of 2 people found this instruction helpful.
  • David from BOTHELL, WA
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Socket set, Wrench (Adjustable)
Everthing went to plan except the wet side of the parts removal was difficult. used puller to remove the wash plate and got it to release. But the plastic part of the wash plate released and left the aluminum part still on the coupling. Corrision was the problem, and I had to again use a puller to remove this part of the wash plate. So it wasn't a matter of just lifting the wash plate off by hand. The rest of the replacement was fine.
Was this helpful?
Thank you for voting!
Washer was noisy, made noise when agitating and spinning.
5 of 11 people found this instruction helpful.
  • Paul from NANTICOKE, PA
  • Really Easy
  • 1- 2 hours
  • Socket set, Wrench (Adjustable)
I had a hard time removing the agitator, had to get thin prybar to get a hold of washplate. After I removed washplate, I found that the shaft that the washplate attaches to was actually worn out. What used to be a spline was smooth. So I ordered a new clutch assembly. There are a lot of bolts that hold the clutch assembly on to the basket. There are a lot of videos on Utube that will walk you through step by step. The only problem I encountered with this was removing the nut that holds the basket to the tub. One video said it was reverse thread, which it wasn’t. You can check the thread on new clutch assembly to see which way is correct. After I put back together. Works like new.
Was this helpful?
Thank you for voting!
Washer was stopping during the spin cycle and making a grinding noise.
2 of 2 people found this instruction helpful.
  • Mike from MANOR, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Our Samsung HE washer started making a grinding noise and stopping at the end of the rinse/spin cycle. I had replaced the clutch and seal 2 years ago and it sounded like it was going out again, however we were not getting the gunk inside the tub like before (seal) and the machine was throwing the tE error code when it stopped which it di d not do last time. According to the manual this meant a thermistor error and the solution was "Call for Service". The machine is 9 years old and way out of warranty so....uh No! I ordered the new thermistor for $15 plus shipping to correct the tE code before looking to replace the clutch again or get a new machine. The new thermistor arrived, leaned the machine on its back, unplug one connector, remove two screws and pull the old one out of it's hole, push the new one in, replace two screws and the connector and GO! Problem fixed! No tE code, no stopping, no grinding noise. As best I can tell, the old thermistor was faulting during the spin cycle and the machine went into emergency stop mode which made the grinding noise. It was not the clutch or bearing at all. Most of the repair time was moving the machine out and disconnecting lines so I could lean it onto its back. Note: If your machine is stopping before draining, it will have water inside the tub which will drain out of the hole where the thermistor goes when you pull the old one out. It has an o-ring to seal it, so just expect a little water to come out and be ready to catch all the water or put the new one in quickly.
Was this helpful?
Thank you for voting!
leg broke off inside housing
5 of 12 people found this instruction helpful.
  • thomas m from CARMICHAEL, CA
  • A Bit Difficult
  • Less than 15 mins
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new leg was a breeze.
Was this helpful?
Thank you for voting!
Drain hose had a pin hole leak external to washer
3 of 6 people found this instruction helpful.
  • Terry from SIMI VALLEY, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
Was this helpful?
Thank you for voting!
very dirty under adjitator cap and pulsator
3 of 7 people found this instruction helpful.
  • Daniel from EDWARDS, IL
  • Very Difficult
  • 1- 2 hours
  • Wrench set
Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,
Was this helpful?
Thank you for voting!
Washer water would not stop running
1 person found this instruction helpful.
  • Willie from Loganville, GA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Turn water valves off , remove the hoses from washer,remove covering from hose housing, remove the claps from back off housing, remove screws from intake housing, remove iPod intake and install new housing and reverse the install
Was this helpful?
Thank you for voting!
Washing machine was displaying te code. Quick google search to diagnose the issue.
1 of 2 people found this instruction helpful.
  • Richard from DICKSON CITY, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Very simple repair after watching YouTube video on how to complete repair.
Was this helpful?
Thank you for voting!
Washer pulsator was coming loose during wash cycle.
1 of 2 people found this instruction helpful.
  • Kristen from Safford, AZ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.
Was this helpful?
Thank you for voting!
could not get the 10 mm nut to loosen
1 of 2 people found this instruction helpful.
  • Marilyn from THOMASTON, GA
  • Very Difficult
  • 30 - 60 mins
  • Nutdriver
Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had
Was this helpful?
Thank you for voting!
Cold water valve leaking.
1 of 2 people found this instruction helpful.
  • Ken from Lakeside, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
turn off the water, unplug washer from power. remove two screws holding rear top plate. Here's the hard part. Pry the rear top plate from the top of the washer. It has multiple snap in guides across the front edge and they are very tight. Be careful and apply steady pressure straight up and they will eventually come free.
I mark ed each of the electrical inputs going to the old valve before removing. Remove the wiring harness. Again be careful and ease them off. the connectors
come apart easily. Remove the hose clamps with pliers and slip off the hoses. They are long enough that I trimmed off the soft ends of the old hoses and still had plenty of hose to reconnect. Remove the filler hoses. Remove the screws holding the valve to the machine. Re install the new valve in reverse order. Goes back in very easily.
Make sure to secure all the hoses. Run a wash cycle with an empty tub to make sure everything is working properly and nothing is leaking. Snap the rear top plate back into position and secure with the two screws Should take less than a couple of hours to do this job. Again the hardest part is getting the rear top plate off.
Was this helpful?
Thank you for voting!
During the spin cycle water continued to flow into the machine.
1 of 3 people found this instruction helpful.
  • Jim from Crystal Lake, IL
  • Really Easy
  • 30 - 60 mins
unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turn ed on water supply valves. Done.
Was this helpful?
Thank you for voting!
WATER WAS NOT SHUTTING OFF
3 of 17 people found this instruction helpful.
  • cathy. from etna, OH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.

LOVE LG CHAT!!!
Was this helpful?
Thank you for voting!
All Instructions for the 31512
16 - 30 of 35