3147 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The oven igniter would glow red but gas did not come on to light the burner.
1 person
found this instruction helpful.
-
Ernest from CINCINNATI, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this helpful?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
1 person
found this instruction helpful.
-
Tara from ALBANY, NY
- Easy
- 15 - 30 mins
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Was this helpful?
Thank you for voting!
broke the igniter in the oven before I even got the oven installed
1 person
found this instruction helpful.
-
june from wills point, TX
- Easy
- 15 - 30 mins
-
Screw drivers
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Was this helpful?
Thank you for voting!
Oven would not start, ignitor was not doing anything
1 person
found this instruction helpful.
-
Michael from Syracuse, NY
- Easy
- 15 - 30 mins
-
Wrench set
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up an
... Read more
d then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.
Read less
Was this helpful?
Thank you for voting!
Oven was slow to get to temp and not holding temp
1 person
found this instruction helpful.
-
Matt from Arlington, AL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing
... Read more
the parts. Working in the oven was by FAR the most difficult part of the entire process.
Read less
Was this helpful?
Thank you for voting!
No heat in oven
1 person
found this instruction helpful.
-
Cynthia from AURORA, MN
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this helpful?
Thank you for voting!
no spark on top burners
2 of 4 people
found this instruction helpful.
-
eric from winter haven, FL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.
Was this helpful?
Thank you for voting!
Igniter was not getting hot enough to allow burner to come on.
1 person
found this instruction helpful.
-
ELMER from BONNEY LAKE, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
Was this helpful?
Thank you for voting!
Replaced upper over light and assembly
1 person
found this instruction helpful.
-
Thomas from SAN DIEGO, CA
- Very Difficult
- More than 2 hours
-
Pliers, Screw drivers
I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light ass
... Read more
embly from the front of the oven and had to go in from the back.
Read less
Was this helpful?
Thank you for voting!
gas oven would not light
1 person
found this instruction helpful.
-
carmine from ABINGTON, PA
- Very Easy
- 30 - 60 mins
-
Screw drivers
Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.
Was this helpful?
Thank you for voting!
Oven was not working at all
1 person
found this instruction helpful.
-
Glynne from Dedham, MA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
Was this helpful?
Thank you for voting!
original fixture required bulb - this fixture (all-in-one) was great
1 person
found this instruction helpful.
-
wesley from ODENVILLE, AL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.
Was this helpful?
Thank you for voting!
Stove Would Not Light To Heat Up.
1 person
found this instruction helpful.
-
Nola from Enid, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Was this helpful?
Thank you for voting!
Gas would come on, would not ignite. Oven not heating.
1 person
found this instruction helpful.
-
Karen from DAYTON, OH
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the
... Read more
brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Read less
Was this helpful?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
1 person
found this instruction helpful.
-
Mz from COLUMBIA, ME
- Very Easy
- Less than 15 mins
-
Pliers
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this helpful?
Thank you for voting!