EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3143 - Instructions

All Instructions for the 3143
16 - 29 of 29

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
washer making noise when washing. rinse and spin was normal.
2 of 2 people found this instruction helpful.
  • David from BOTHELL, WA
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Socket set, Wrench (Adjustable)
Everthing went to plan except the wet side of the parts removal was difficult. used puller to remove the wash plate and got it to release. But the plastic part of the wash plate released and left the aluminum part still on the coupling. Corrision was the problem, and I had to again use a puller to remove this part of the wash plate. So it wasn't a matter of just lifting the wash plate off by hand. The rest of the replacement was fine.
Was this helpful?
Thank you for voting!
Washer was noisy, made noise when agitating and spinning.
5 of 11 people found this instruction helpful.
  • Paul from NANTICOKE, PA
  • Really Easy
  • 1- 2 hours
  • Socket set, Wrench (Adjustable)
I had a hard time removing the agitator, had to get thin prybar to get a hold of washplate. After I removed washplate, I found that the shaft that the washplate attaches to was actually worn out. What used to be a spline was smooth. So I ordered a new clutch assembly. There are a lot of bolts that hold the clutch assembly on to the basket. There are a lot of videos on Utube that will walk you through step by step. The only problem I encountered with this was removing the nut that holds the basket to the tub. One video said it was reverse thread, which it wasn’t. You can check the thread on new clutch assembly to see which way is correct. After I put back together. Works like new.
Was this helpful?
Thank you for voting!
Drain hose had a pin hole leak external to washer
3 of 6 people found this instruction helpful.
  • Terry from SIMI VALLEY, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
Was this helpful?
Thank you for voting!
leg broke off inside housing
5 of 12 people found this instruction helpful.
  • thomas m from CARMICHAEL, CA
  • A Bit Difficult
  • Less than 15 mins
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new leg was a breeze.
Was this helpful?
Thank you for voting!
Washer water would not stop running
1 person found this instruction helpful.
  • Willie from Loganville, GA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Turn water valves off , remove the hoses from washer,remove covering from hose housing, remove the claps from back off housing, remove screws from intake housing, remove iPod intake and install new housing and reverse the install
Was this helpful?
Thank you for voting!
very dirty under adjitator cap and pulsator
3 of 7 people found this instruction helpful.
  • Daniel from EDWARDS, IL
  • Very Difficult
  • 1- 2 hours
  • Wrench set
Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,
Was this helpful?
Thank you for voting!
Washer pulsator was coming loose during wash cycle.
1 of 2 people found this instruction helpful.
  • Kristen from Safford, AZ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.
Was this helpful?
Thank you for voting!
could not get the 10 mm nut to loosen
1 of 2 people found this instruction helpful.
  • Marilyn from THOMASTON, GA
  • Very Difficult
  • 30 - 60 mins
  • Nutdriver
Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had
Was this helpful?
Thank you for voting!
Cold water valve leaking.
1 of 2 people found this instruction helpful.
  • Ken from Lakeside, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
turn off the water, unplug washer from power. remove two screws holding rear top plate. Here's the hard part. Pry the rear top plate from the top of the washer. It has multiple snap in guides across the front edge and they are very tight. Be careful and apply steady pressure straight up and they will eventually come free.
I mark ed each of the electrical inputs going to the old valve before removing. Remove the wiring harness. Again be careful and ease them off. the connectors
come apart easily. Remove the hose clamps with pliers and slip off the hoses. They are long enough that I trimmed off the soft ends of the old hoses and still had plenty of hose to reconnect. Remove the filler hoses. Remove the screws holding the valve to the machine. Re install the new valve in reverse order. Goes back in very easily.
Make sure to secure all the hoses. Run a wash cycle with an empty tub to make sure everything is working properly and nothing is leaking. Snap the rear top plate back into position and secure with the two screws Should take less than a couple of hours to do this job. Again the hardest part is getting the rear top plate off.
Was this helpful?
Thank you for voting!
During the spin cycle water continued to flow into the machine.
1 of 3 people found this instruction helpful.
  • Jim from Crystal Lake, IL
  • Really Easy
  • 30 - 60 mins
unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turn ed on water supply valves. Done.
Was this helpful?
Thank you for voting!
WATER WAS NOT SHUTTING OFF
3 of 17 people found this instruction helpful.
  • cathy. from etna, OH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.

LOVE LG CHAT!!!
Was this helpful?
Thank you for voting!
All Instructions for the 3143
16 - 29 of 29