This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
Clothing moves over a covered mounting point with help from this washer pulsator cap. The round plastic cover snaps into the center of the washplate, concealing the mounting bolt and providing a smooth surface above it. Cracks, broken retaining tabs, or a missing cap may expose the hardware or allow the cover to come loose during washing....Read more Replacing a damaged cap restores the finished washplate surface and helps keep garments from catching around the recessed bolt opening as laundry moves through the wash cycle. This is an OEM part sourced directly from the manufacturer.
This is a pulsator assembly, also known as an agitator, for your washing machine. This pulsator sits at the bottom of your washer and is what is used as the main driving force to wash your clothes. If the pulsator in your washer is broken, it will need replacing immediately to continue to wash and clean your clothes evenly. The cap that sits in the center of this part is sold separately.
Drain used wash water with this top-load washer drain pump assembly. Its motor drives an internal impeller that pushes water from the tub through the drain hose during drain and spin cycles. A worn motor, damaged impeller, or leaking housing may cause standing water, slow draining, loud buzzing, or puddles beneath the machine. Replacing a...Read more faulty pump helps restore proper drainage so wash cycles can finish normally. Unplug the washer, shut off the water supply, and prepare for leftover water before disconnecting hoses or wiring. This is an OEM part sourced directly from the manufacturer.
This washer tub-to-pump drain hose carries used water from the outer tub to the drain pump during draining. Its flexible, corrugated design accommodates tub movement while keeping water contained within the drainage path. Cracks, splits, or worn sections may cause leaks beneath the washer, while a collapsed section can restrict flow and l...Read moreeave water in the tub. Replacing a damaged hose helps restore proper drainage and a secure connection between the tub and pump, allowing wastewater to move out during wash and rinse cycles. This is an OEM part sourced directly from the manufacturer.
Smooth lid movement starts with a secure pivot point, and this washer top lid hinge connects the lid to the top panel. It supports the lid as it opens and closes, helping it stay aligned with the washer opening. A cracked, bent, or worn hinge may cause the lid to sit unevenly, shift sideways, or become difficult to close. Replacing a dama...Read moreged hinge helps restore steady support and proper lid movement. Unplug the washer and support the lid before removing the hinge. This is an OEM part sourced directly from the manufacturer.
This clutch housing assembly with mode shifter, or washer drive shaft and shifter assembly, is made for your washer. It connects the appliance wash plate to the motor so the washer can shift the drive system between the appliance spin and agitate cycles. Is measures 14.5 inches in diameter. You may need to replace this part if you hear strange noises or if the washer will not spin or agitate.
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pump, and it is responsible for transporting water out of the washing machine after a cycle. If the drain hose is kinked, damaged, or clogged, ...Read morethe washer will leak, or you may find standing water in the drum at the end of the cycle. Each drain hose comes with a metal clamp for fastening.
Secure attachment of washer components depends on fasteners that hold firmly during operation. This replacement washer screw restores an attachment where the original screw is missing, stripped, or damaged. Worn threads or a damaged head may prevent proper tightening and leave the attached component loose. Replacing faulty hardware helps ...Read morerestore a firm connection when the receiving threads and surrounding material remain intact. The screw can also be replaced during reassembly if damage prevents the original fastener from being tightened or removed normally. This is an OEM part sourced directly from the manufacturer.
Accurate water level sensing helps the washer fill and advance through its cycles correctly. This pressure sensor assembly measures changes in air pressure through a connected tube as water enters or leaves the tub. It sends water level information to the electronic control so filling can stop at the required level. A faulty sensor may ca...Read moreuse overfilling, underfilling, or interrupted wash cycles. Replacing a failed assembly helps restore reliable level feedback and controlled filling throughout the wash and rinse stages. This is an OEM part sourced directly from the manufacturer.
A secure hose connection helps keep water contained inside the appliance. This hose clamp applies pressure around the hose end, holding it firmly against its fitting during operation. A weakened, bent, or broken clamp may allow the connection to loosen and leak into the cabinet or onto the floor. Replacing a damaged clamp helps restore th...Read moree grip needed to keep the hose attached and sealed. It secures the connection while allowing the hose to be removed when maintenance or replacement is required. This is an OEM part sourced directly from the manufacturer.
This is a replacement screw, also known as a shear pin that is used in several pieces of outdoor power equipment. It is made of metal and is approximately 2 inches in length. It is a hex head screw and is sold individually. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
It did not drain water, cycle stops at rinse+spin.
28 of 36 peoplefound this instruction helpful.
Jesus from El Paso, TX
Very Easy
15 - 30 mins
Socket set, Wrench set
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su
... Read morepplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
Read less
Was this helpful?
Thank you for voting!
The right side hinge that holds the washer top door broke and needed to be replaced.
18 of 20 peoplefound this instruction helpful.
John from SAN JOSE, CA
Very Easy
15 - 30 mins
Screw drivers
Popped out the plastic "doors" that cover the metal actuators. Removed the metal actuators on both right and left sides of the door then unscrewed (3 screws each actuator) them from door frame. Slid the actuators out to enable the door to be removed. Unscrewed 2 screws on the top front of the washer which enabled me to angle the top of
... Read more the washer to expose the screws that hold the plastic hinges. Unscrewed the hinges (2 screws each) and replaced both of the hinges (I figured I'd do both of them now so I don't have to do it again for another 15 years). Put everything back together and all works like new.
Read less
Was this helpful?
Thank you for voting!
Water continued leaking into washer after the end of cycle through the water inlet valve.
14 of 19 peoplefound this instruction helpful.
Flora from MIAMI, FL
Very Easy
30 - 60 mins
Screw drivers, Wrench (Adjustable)
Did the repair Myself. Saved $ 400.00 in the process.