3129 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Reistall shelf
-
Oleg from Lees Summit, MO
- Really Easy
- Less than 15 mins
Replaced cap and reinstalled. But I used iron nail inside cover to hold right side because crack was at right hole and right part would not help.
Was this helpful?
Thank you for voting!
needed new light socket
-
Charles from Williamsburg, VA
- Really Easy
- Less than 15 mins
Pulled out old socket.pushed in new one.
Was this helpful?
Thank you for voting!
compressor running and hot, refer and fridge room temp.
-
Charles from Durham, CA
- Really Easy
- Less than 15 mins
Watched a youtube on capacitors- though on a motor with a pulley, the symptoms were the same, motor running and pulley not turning-bad capacitor. Took a chance for a 17+ dollar part vs a new compressor. It worked.
Was this helpful?
Thank you for voting!
door shelf end cap broke off
-
Leonard from Niagara Falls, NY
- Really Easy
- Less than 15 mins
easily popped the new one in.
Was this helpful?
Thank you for voting!
Freezer And Frig Both Warm And Compressor Would Not Run
-
joe from decatur, GA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and
... Read more
saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.
Read less
Was this helpful?
Thank you for voting!
Refrigerator and freezer drawer would not maintain set temperature
-
James from Bel Air, MD
- A Bit Difficult
- 30 - 60 mins
-
Socket set
Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I o
... Read more
rdered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.
Read less
Was this helpful?
Thank you for voting!
Refrig would not cool, freezer worked fine
-
Edward from McKinney, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Barry G was right on with instructions and expectations of the process to trouble shoot parts and how to replace. Barry also provide the right part numbers for replacement items. Thanks again Barry.
Was this helpful?
Thank you for voting!
the new motor was slightly larger than the old one and the bracket does not fit
-
Patricia from Oxford, MI
- Easy
- 1- 2 hours
-
Screw drivers
Had to get behind the refrigerator and clean the drain out first and that took at least and hour. Just unplug the old motor. Took the old parts of the old motor, put them on the new one and plugged it back in.
Was this helpful?
Thank you for voting!