3126 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
1 person
found this instruction helpful.
-
FRANCES from AFFTON, MO
- Very Easy
- Less than 15 mins
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
My light in the refrigerator was going on and off.
1 person
found this instruction helpful.
-
Nan from PURCELLVILLE, VA
- Very Easy
- Less than 15 mins
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this helpful?
Thank you for voting!
Burners would not lite
2 of 4 people
found this instruction helpful.
-
Lloyd from Cocoa, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped. Thanks Lloyd
Was this helpful?
Thank you for voting!
Start relay burned
1 person
found this instruction helpful.
-
Carlos from Copper Canyon, OK
- Very Easy
- 15 - 30 mins
-
Screw drivers
Unplug the refrigerator removed the condenser/ compressor cover back bottom on fridge, remove the relay from the compressor took off the two wires, replace with new relay
Was this helpful?
Thank you for voting!
Gas would come on, would not ignite. Oven not heating.
1 person
found this instruction helpful.
-
Karen from DAYTON, OH
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the
... Read more
brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Read less
Was this helpful?
Thank you for voting!
Oven did not ignite
1 of 2 people
found this instruction helpful.
-
John from Racine, WI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..
Was this helpful?
Thank you for voting!
Needed to replace two stove valve knobs.
1 of 2 people
found this instruction helpful.
-
Roberta from BROOKLYN, NY
- Really Easy
- Less than 15 mins
Inserting two stove valve knobs took 10 seconds! No tools necessary.
Was this helpful?
Thank you for voting!
Short in the light socket.
1 of 2 people
found this instruction helpful.
-
ED from ENON, OH
- Very Easy
- Less than 15 mins
Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.
Was this helpful?
Thank you for voting!
Thermostat bulb was hanging loose
2 of 5 people
found this instruction helpful.
-
Willi from Old Saybrook, CT
- Really Easy
- Less than 15 mins
-
Pliers
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this helpful?
Thank you for voting!
Old and corroded drip pans
1 of 2 people
found this instruction helpful.
-
Veronica from Miami Beach, FL
- Really Easy
- Less than 15 mins
Furtunately, it was just a replacement of the drip pans. It changed the entite looks of my range for under $ 25.00 dollars. Very satisfied!
Was this helpful?
Thank you for voting!
Drip pans were rusted. I had shopped for replacements at local appliance stores without finding them.
1 of 2 people
found this instruction helpful.
-
Norma J from Philadelphia, PA
- Really Easy
- Less than 15 mins
Removed the rusted drip pans and replaced them with the new pans. Range looks great and ready for many more years of use!
Was this helpful?
Thank you for voting!
Oven ignitor would glow but took 30 - 40 mins to heat
1 of 2 people
found this instruction helpful.
-
Catherine from Newton, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!
Was this helpful?
Thank you for voting!
Bottom oven burner wouldn't light.
1 of 2 people
found this instruction helpful.
-
James from Lino Lakes, MN
- Easy
- Less than 15 mins
-
Nutdriver
If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.
Was this helpful?
Thank you for voting!
Oven wouldn't heat. Igniter was broken.
1 of 2 people
found this instruction helpful.
-
Thomas from Allison Park, PA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
Was this helpful?
Thank you for voting!