EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3121X Magic Chef Range - Instructions

All Instructions for the 3121X
121 - 135 of 279

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Screws in the old unit were frozen and stripped
0 of 1 people found this instruction helpful.
  • Lee from Cave Junction, OR
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
During removal of the original ignitor the screws would not come out. they were rusted. using some liquid wrenchI tried to remove them again and they broke. Using an angle drill and special bits I was able to drill out the screws. I re- tapped the holes and the repair was simple. My wiring required additional insulation over the supplied wiring that came with the new ignitor. Cut the wires about 1 1/2 inches from the plug and added the insulation then replaced the plug with the provided wire nuts. Mounted the new unit and all tested perfectly. Closed up oven and operates perfect as if new.
Was this helpful?
Thank you for voting!
Oven would take too long to light
0 of 1 people found this instruction helpful.
  • Carlos from New York, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
I am a novice at this, so before I did anything I researched this site and made sure to read the installation directions that came with the part.

First I removed the oven racks, the bottom cover (one screw in front and two back latches by moving them towards me) and the fire cover underneath that. Next I disconnected the elec trical plug in the back.
Then I removed the defective part by unscrewing 2 back panel screws and 1 on the side of the igniter itself. Now, in connecting the new igniter I cut the connector off of the old one and wire nut connected it to the new one. I did check the connectors and cleaned them by simply plugging/ unplugging them a few times.
Next, The trickiest thing about installing the new igniter was pushing the wires all the way to the back of the oven. I took care and time in this to insure that the connection was well insulated from the heat and then plugged the hole with the insulation material supplied. Next I recconected the fire cover and turned it on. Worked great! Put everything back together, plugged it in and Voila! Like new.
Was this helpful?
Thank you for voting!
Oven quit lighting
0 of 1 people found this instruction helpful.
  • MIKE from Phelan, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver
I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for years because I didn't realize how easy the fix was.
Was this helpful?
Thank you for voting!
gas would go on and off -- oven slow to heat
0 of 1 people found this instruction helpful.
  • Stephen from Evanston, IL
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers
Remove lower pan. This is tricky -- pull clips at the back of the pan forward (they may stick), Then push pan to back and lift forward portion up, exposing igniter and gas tube. Use nut driver or socket set to unscrew the two mounting screws. Had to use pliers at one point to pull on screws while turning as they were cross-threaded, perha ps due to heat. Cut wires to igniter. Pull out oven and look at exterior back of stove -- at bottom near the center opening. The power feeder wires to the igniter are red and terminate in a jack -- disconnect the igniter plug connector and pull the cut wire through. Back to the inside of the stove: you now have to force the connector for the new igniter through the insulation at the back. Pull some of the old insulation out to make this possible -- new insulation is provided in the kit. Then at back of stove connect new igniter plug to power feed jack. Then screw in new igniter with the original screws. I had to use pliers again while turning to force them past the cross-threaded area. Replace bottom pan and you are in business, saving a lot of money!!
Was this helpful?
Thank you for voting!
failed igniter
0 of 1 people found this instruction helpful.
  • David from Easton, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
First, I removed the racks, door, bottom drawer, and lifted the bottom pan up and out from the rear. Then, I unscrewed the bottom cover for the electrical stuff (under where the drawer is) as this is where the connector for the igniter is. I did a voltage test on the oven side of the connector, finding voltage there I removed the igniter by removing the 2 screws holding it to the burner. (pack lunch for that part, they will be rusted, I used a mini grinder to cut off the heads). Then I pulled the connector through the hole, and installed new igniter using self drilling screws. After i repacked the insulation, I put it back together, and it lit right up. The failed one had a bad ballast, confirmed by a continuity test.
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people found this instruction helpful.
  • joan from florissant, MO
  • Easy
  • 15 - 30 mins
  • Screw drivers
My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.
Was this helpful?
Thank you for voting!
My Gas Oven Wasn't Lighting and it Scared Me!
0 of 1 people found this instruction helpful.
  • Kim from Cedar River, MI
  • Easy
  • 15 - 30 mins
  • Screw drivers
I was worried over the fact that my oven was filling up with propane but taking a long time to light. One day it didn't light for over ten minutes. I shut it off and put the still frozen pizza back in the freezer. That's it, I thought. I'm not going to use the oven again until it's fixed.

I looked online and ordered the part. It came within two days time,even though it was a weekend during the holiday season. My husband spent about 15 minutes with his head in the oven and then said it was fixed.

I baked several batches of Christmas cookies and three coffee cakes the next day.
Was this helpful?
Thank you for voting!
The oven gas valve would not turn on
0 of 1 people found this instruction helpful.
  • Steve from Prospect Heights, IL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Replaced the oven ignitor. Toughest part was removing old screws.
Was this helpful?
Thank you for voting!
Things cooked in the oven were taking longer than usual to be done.
0 of 1 people found this instruction helpful.
  • Ron from Belleville, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the ignit er came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.
Was this helpful?
Thank you for voting!
Oven burner would night ignite
0 of 1 people found this instruction helpful.
  • Douglas from Hanover Park, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Replaced the ceramic glow ignitor by removeing the two screws holding it to the mounting bracket. Gas and electric were tturned off. Unplugged the ignitor from rear of oven. Installed new switch in the same way and if worked perfect. Part was ordered online for $48. I saved one hundred dollars by doing it myself. My outdoor grill was hard er than this.
Was this helpful?
Thank you for voting!
Oven would't heat
0 of 1 people found this instruction helpful.
  • Sidney from Hindman, KY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!
Was this helpful?
Thank you for voting!
oven did not reach temperature and was slow to heat up
0 of 1 people found this instruction helpful.
  • kevin from west pittston, PA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
remove racks out of the oven. remove very bottom of oven and you will then have access to the ignitor.the part was a little difficult to remove due to the self tapping screws snapping upon removal.drilled them out and installed new ignitor.oven now works fantastic.
Was this helpful?
Thank you for voting!
ignitor would heat enough to open gas vavle to lite oven
0 of 1 people found this instruction helpful.
  • Jon from Mayville, NY
  • Really Easy
  • 15 - 30 mins
  • Socket set
unplugged the oven, unplugged the ignitor and removed the two screws
Was this helpful?
Thank you for voting!
Oven would not light, but igniter would glow.
0 of 1 people found this instruction helpful.
  • Roger from Greenwood, AR
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.
Was this helpful?
Thank you for voting!
would not light oven
0 of 1 people found this instruction helpful.
  • rick from chariton, IA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
2 screws easy to remove and plug in the wire. job done.
Was this helpful?
Thank you for voting!
All Instructions for the 3121X
121 - 135 of 279