EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3121S Magic Chef Range - Instructions

All Instructions for the 3121S
121 - 135 of 283

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Our oven took a long time to light and come up to temperature. Very frustrating since I cook and bake a lot!
0 of 1 people found this instruction helpful.
  • ALISE from LUDLOW, MA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
First we removed the two screws that hold the element in place. Then detached the wire from underneath the oven. We then had to pull out the oven to access the back panel. We unscrewed the back panel and detached the second wire. Then we revearsed the process and installed the new igniter. The whole thing from start to finish took ab out 35min. This was very easy to do and I am happily baking once again. The whole family is happy about that :)
Was this helpful?
Thank you for voting!
Faulty Ignitor
0 of 1 people found this instruction helpful.
  • Emanuel from Satsuma, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Our oven failed to cook in the Bake mode. I was thinking I needed to have a repairman come service it. I got the product manual & begin to do some research. I thought the problem was was in the control panel until a parts search took me to the Parts Select website where I read the other successful repair stories & the most likely reason i t did not work. It was real simple. The only problem I had was a screw that held the ignitor stripped & I had to cut the head off. The directions sent with the part were dead on. I then simply installed new ignitor & presto - it works! My wire connection required stripping the wires & using the ceramic wirenuts. I am glad I found Part Select & will call again when needed!! Thanks !!
Was this helpful?
Thank you for voting!
Oven would no longer ignite
0 of 1 people found this instruction helpful.
  • Karen from Hammond Ranch, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers
My oven would no longer ignite, and I asked a friend to help me see if we could fix it. We found an appliance repair manual online (www.appliancerepair.net), and it described that the most likely part needing replacement was the ceramic igniter - they do wear out, and my oven was - after all - over 20 yrs old, with never a repair! Then, somehow I found this PartSelect website, and after entering the make and model number, it showed the part, with a drawing, and dimensions - enough for me to be convinced it was the right part. I called and was reassured that if it were not the right part, it would be easy to return / refund. So, I ordered the part, standard shipping .... and to my great surprise, it was delivered the VERY NEXT DAY to my front door! And this was right before Christmas, a very busy time! The oven works like a charm now..... (I also had to clean out some of the gas holes, which can build up residues over time.) This repair cost less than $50, I'm sure if an appliance repair person came out it would have been more like $200 - not worth it for an oven this old. So, I'm happy with PartSelect!
Was this helpful?
Thank you for voting!
Oven would not heat to temp and could smell gas.
0 of 1 people found this instruction helpful.
  • Christopher from Dearborn, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Was this helpful?
Thank you for voting!
very slow heating, smell of gas
0 of 1 people found this instruction helpful.
  • Carole from Girdwood, AK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Was this helpful?
Thank you for voting!
Oven Would not Light
0 of 1 people found this instruction helpful.
  • Neville from Lithonia, GA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.
Was this helpful?
Thank you for voting!
Oven quit lighting
0 of 1 people found this instruction helpful.
  • MIKE from Phelan, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver
I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for years because I didn't realize how easy the fix was.
Was this helpful?
Thank you for voting!
gas would go on and off -- oven slow to heat
0 of 1 people found this instruction helpful.
  • Stephen from Evanston, IL
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers
Remove lower pan. This is tricky -- pull clips at the back of the pan forward (they may stick), Then push pan to back and lift forward portion up, exposing igniter and gas tube. Use nut driver or socket set to unscrew the two mounting screws. Had to use pliers at one point to pull on screws while turning as they were cross-threaded, perha ps due to heat. Cut wires to igniter. Pull out oven and look at exterior back of stove -- at bottom near the center opening. The power feeder wires to the igniter are red and terminate in a jack -- disconnect the igniter plug connector and pull the cut wire through. Back to the inside of the stove: you now have to force the connector for the new igniter through the insulation at the back. Pull some of the old insulation out to make this possible -- new insulation is provided in the kit. Then at back of stove connect new igniter plug to power feed jack. Then screw in new igniter with the original screws. I had to use pliers again while turning to force them past the cross-threaded area. Replace bottom pan and you are in business, saving a lot of money!!
Was this helpful?
Thank you for voting!
failed igniter
0 of 1 people found this instruction helpful.
  • David from Easton, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
First, I removed the racks, door, bottom drawer, and lifted the bottom pan up and out from the rear. Then, I unscrewed the bottom cover for the electrical stuff (under where the drawer is) as this is where the connector for the igniter is. I did a voltage test on the oven side of the connector, finding voltage there I removed the igniter by removing the 2 screws holding it to the burner. (pack lunch for that part, they will be rusted, I used a mini grinder to cut off the heads). Then I pulled the connector through the hole, and installed new igniter using self drilling screws. After i repacked the insulation, I put it back together, and it lit right up. The failed one had a bad ballast, confirmed by a continuity test.
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people found this instruction helpful.
  • joan from florissant, MO
  • Easy
  • 15 - 30 mins
  • Screw drivers
My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.
Was this helpful?
Thank you for voting!
Oven burner would night ignite
0 of 1 people found this instruction helpful.
  • Douglas from Hanover Park, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Replaced the ceramic glow ignitor by removeing the two screws holding it to the mounting bracket. Gas and electric were tturned off. Unplugged the ignitor from rear of oven. Installed new switch in the same way and if worked perfect. Part was ordered online for $48. I saved one hundred dollars by doing it myself. My outdoor grill was hard er than this.
Was this helpful?
Thank you for voting!
My Gas Oven Wasn't Lighting and it Scared Me!
0 of 1 people found this instruction helpful.
  • Kim from Cedar River, MI
  • Easy
  • 15 - 30 mins
  • Screw drivers
I was worried over the fact that my oven was filling up with propane but taking a long time to light. One day it didn't light for over ten minutes. I shut it off and put the still frozen pizza back in the freezer. That's it, I thought. I'm not going to use the oven again until it's fixed.

I looked online and ordered the part. It came within two days time,even though it was a weekend during the holiday season. My husband spent about 15 minutes with his head in the oven and then said it was fixed.

I baked several batches of Christmas cookies and three coffee cakes the next day.
Was this helpful?
Thank you for voting!
oven would not ignite
0 of 1 people found this instruction helpful.
  • Alan from Cinnaminson, NJ
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
removed door (pull up and out), removed all racks and bottom of oven, removed two screws holding old igniter, unplugged old igniter from harness, mounted new igniter using two screws and nuts purchased from local hardware store, plugged new igniter into harness, replaced bottom of oven and trays, slid oven door down over hinges. Oven wor ks properly. Thanx!
Was this helpful?
Thank you for voting!
oven did not reach temperature and was slow to heat up
0 of 1 people found this instruction helpful.
  • kevin from west pittston, PA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
remove racks out of the oven. remove very bottom of oven and you will then have access to the ignitor.the part was a little difficult to remove due to the self tapping screws snapping upon removal.drilled them out and installed new ignitor.oven now works fantastic.
Was this helpful?
Thank you for voting!
ignitor would heat enough to open gas vavle to lite oven
0 of 1 people found this instruction helpful.
  • Jon from Mayville, NY
  • Really Easy
  • 15 - 30 mins
  • Socket set
unplugged the oven, unplugged the ignitor and removed the two screws
Was this helpful?
Thank you for voting!
All Instructions for the 3121S
121 - 135 of 283