3121S Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
1 person
found this instruction helpful.
-
Mz from COLUMBIA, ME
- Very Easy
- Less than 15 mins
-
Pliers
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this helpful?
Thank you for voting!
Oven was not working at all
1 person
found this instruction helpful.
-
Glynne from Dedham, MA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
Was this helpful?
Thank you for voting!
original fixture required bulb - this fixture (all-in-one) was great
1 person
found this instruction helpful.
-
wesley from ODENVILLE, AL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.
Was this helpful?
Thank you for voting!
gas oven would not light
1 person
found this instruction helpful.
-
carmine from ABINGTON, PA
- Very Easy
- 30 - 60 mins
-
Screw drivers
Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.
Was this helpful?
Thank you for voting!
Replaced upper over light and assembly
1 person
found this instruction helpful.
-
Thomas from SAN DIEGO, CA
- Very Difficult
- More than 2 hours
-
Pliers, Screw drivers
I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light ass
... Read more
embly from the front of the oven and had to go in from the back.
Read less
Was this helpful?
Thank you for voting!
The oven igniter would glow red but gas did not come on to light the burner.
1 person
found this instruction helpful.
-
Ernest from CINCINNATI, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this helpful?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
1 person
found this instruction helpful.
-
Tara from ALBANY, NY
- Easy
- 15 - 30 mins
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Was this helpful?
Thank you for voting!
Igniter was not getting hot enough to allow burner to come on.
1 person
found this instruction helpful.
-
ELMER from BONNEY LAKE, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
Was this helpful?
Thank you for voting!
Oven would not start, ignitor was not doing anything
1 person
found this instruction helpful.
-
Michael from Syracuse, NY
- Easy
- 15 - 30 mins
-
Wrench set
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up an
... Read more
d then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.
Read less
Was this helpful?
Thank you for voting!
broke the igniter in the oven before I even got the oven installed
1 person
found this instruction helpful.
-
june from wills point, TX
- Easy
- 15 - 30 mins
-
Screw drivers
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Was this helpful?
Thank you for voting!
No heat in oven
1 person
found this instruction helpful.
-
Cynthia from AURORA, MN
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this helpful?
Thank you for voting!
Oven was slow to get to temp and not holding temp
1 person
found this instruction helpful.
-
Matt from Arlington, AL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing
... Read more
the parts. Working in the oven was by FAR the most difficult part of the entire process.
Read less
Was this helpful?
Thank you for voting!
Oven making whooshing sound and not heating up
1 of 2 people
found this instruction helpful.
-
Jason from Williamsburg, VA
- Easy
- 15 - 30 mins
-
Screw drivers
Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!
Was this helpful?
Thank you for voting!
Replacement of igniter
1 of 2 people
found this instruction helpful.
-
Robert from Orange, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.
Was this helpful?
Thank you for voting!
The broiler would not lite at all and the oven would lite occasionally but would not maintain temperature.
1 of 2 people
found this instruction helpful.
-
Vincent from Lewes, DE
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I replaced the igniter in both the oven and the broiler. This was my first time ever working on a range.
I removed the oven door for easy access. To replace the oven igniter, I took the bottom floor out of the oven. The igniter is readily visible at the rear of the burner. I removed the two screws holding the igniter with a socket ... Read more wrench. The screws were somewhat stubborn but yielded rather quickly. I gently pulled the two wires attached to the igniter from the back of the oven until the connector was exposed. I disconnected the old igniter and connected the new one. Then I simply reversed the the procedure, tucking the connector and wire back through the hole it came from and re - installed the two screws in the bracket. The insulation provided with the kit was used to plug the hole in the back of the oven.
To replace the broiler igniter, I essentially followed the same procedure. However, I chose not to remove the broiler baffle. This made it more difficult to both remove and re-install the two screws holding the ignitor. Otherwise, everything else went smoothly. If I had to do it again, I'd remove the baffle.
I removed the oven door for easy access. To replace the oven igniter, I took the bottom floor out of the oven. The igniter is readily visible at the rear of the burner. I removed the two screws holding the igniter with a socket ... Read more wrench. The screws were somewhat stubborn but yielded rather quickly. I gently pulled the two wires attached to the igniter from the back of the oven until the connector was exposed. I disconnected the old igniter and connected the new one. Then I simply reversed the the procedure, tucking the connector and wire back through the hole it came from and re - installed the two screws in the bracket. The insulation provided with the kit was used to plug the hole in the back of the oven.
To replace the broiler igniter, I essentially followed the same procedure. However, I chose not to remove the broiler baffle. This made it more difficult to both remove and re-install the two screws holding the ignitor. Otherwise, everything else went smoothly. If I had to do it again, I'd remove the baffle.
Read less
Was this helpful?
Thank you for voting!