3120S Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freont Burners Of Both Units Had Rusted Though Over The Years Of Boilover.
3 of 4 people
found this instruction helpful.
-
Angelo W. from Chirfland, FL
- Really Easy
- Less than 15 mins
Lifted lid, removed old burner units, replace with new ones. In less than two min. Was back up and cooking.
Was this helpful?
Thank you for voting!
Stove top had burnt marks from long use
3 of 4 people
found this instruction helpful.
-
MEEWAN from BUENA PARK, CA
- Really Easy
- Less than 15 mins
Just replaced the top.
No tool or repair was needed.
Parts arrived earlier than promised, so it was awesome!
No tool or repair was needed.
Parts arrived earlier than promised, so it was awesome!
Was this helpful?
Thank you for voting!
floor panel heavily stained and warped
3 of 5 people
found this instruction helpful.
-
Joel from Monroe, NY
- Really Easy
- Less than 15 mins
slide latches in rear of floor panel forward and remove.
Was this helpful?
Thank you for voting!
1960's oven door gasket fell apart, actual gasket not available any more
2 of 2 people
found this instruction helpful.
-
Mary from WINCHESTER, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Was this helpful?
Thank you for voting!
gas range knob and oven knob for my magic chief stove broke
2 of 2 people
found this instruction helpful.
-
Sandra from MONTCLAIR, NJ
- Really Easy
- 30 - 60 mins
After going to Homedepot, Sears, Lowes and other hardware stores I reached out to some folks at my job i was recommended to order the parts from PartSelect. I spent the Christmas and New Years Holiday in a mess. I really could not cook like i wanted to. I ordered the parts within a week it came. I am thankful you to guys no more drama,
... Read more
caos or worries. I highly recommend this site very easy to install. thank you
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Range burner drip pans were rusted and old
3 of 6 people
found this instruction helpful.
-
Billye from San Antonio, TX
- Really Easy
- 15 - 30 mins
The repair was super simple, just remove the drip pan and place new one.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the fu ... Read more ture for needed parts.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the fu ... Read more ture for needed parts.
Read less
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people
found this instruction helpful.
-
Rhoda P. from Secaucus, NJ
- Really Easy
- Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken burner knobs on stove.
2 of 3 people
found this instruction helpful.
-
Barbara L. from Tewksbury, MA
- Really Easy
- Less than 15 mins
Just replaced the old burner knobs with the new !!!
Was this helpful?
Thank you for voting!
rusty drip trays
2 of 3 people
found this instruction helpful.
-
Pam from Grand Ledge, MI
- Really Easy
- Less than 15 mins
finally after years of searching for trays of this size with no luck in local stores, I was able to find and purchase 2 sets, one set for my daughter, which we were able to put in place to clean up our stoves and make them more appealing . Thank-you for your prompt service.
Was this helpful?
Thank you for voting!
Install valve knobs
3 of 6 people
found this instruction helpful.
-
Donald from Peebles, OH
- Really Easy
- Less than 15 mins
This was not a difficult task. I just slid the valve knob on the shaft, repair was complete. This was a very easy diy project.
Was this helpful?
Thank you for voting!
needed a new knob
2 of 4 people
found this instruction helpful.
-
Clayton from Shortsville, NY
- Really Easy
- Less than 15 mins
pulled the old one off and push the new one on
Was this helpful?
Thank you for voting!
The burners were old and loose
2 of 4 people
found this instruction helpful.
-
James R. from Corona, CA
- Really Easy
- Less than 15 mins
First, I raised the top. Extracted the holding pin, Then replaced the burner. Then reinserted the holding pin. Two minutes top's.
Other Parts Used:
Was this helpful?
Thank you for voting!
new knob
2 of 4 people
found this instruction helpful.
-
Marvin from Pahrump, NV
- Really Easy
- Less than 15 mins
Pulled one knob off and pushed the other one on.
Was this helpful?
Thank you for voting!
My oven door seal had dried rotted
1 person
found this instruction helpful.
-
Anita from ELKTON, VA
- Really Easy
- 15 - 30 mins
-
Pliers
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this helpful?
Thank you for voting!
The oven control know wore out.
1 person
found this instruction helpful.
-
Judy from ARDSLEY, NY
- Really Easy
- Less than 15 mins
I purchased a knob that I was hoping might fit properly.
Unfortunately I did not find anything that matched the knob we had originally. We use the knob that I purchased to turn the oven on and off, but the shaft channel is much longer than the shaft on the stove, so the knob sits high above the other knobs. I wish that I could find ... Read more a knob to accommodate the
shaft on the stove. I have considered purchasing an addition kinob and trying to saw off part of the shaft if the plastic can be shortened without shattering.
Unfortunately I did not find anything that matched the knob we had originally. We use the knob that I purchased to turn the oven on and off, but the shaft channel is much longer than the shaft on the stove, so the knob sits high above the other knobs. I wish that I could find ... Read more a knob to accommodate the
shaft on the stove. I have considered purchasing an addition kinob and trying to saw off part of the shaft if the plastic can be shortened without shattering.
Read less
Was this helpful?
Thank you for voting!