EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3115 - Instructions

All Instructions for the 3115
91 - 105 of 304

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
My oven door seal had dried rotted
1 person found this instruction helpful.
  • Anita from ELKTON, VA
  • Really Easy
  • 15 - 30 mins
  • Pliers
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this helpful?
Thank you for voting!
Oven would not start, ignitor was not doing anything
1 person found this instruction helpful.
  • Michael from Syracuse, NY
  • Easy
  • 15 - 30 mins
  • Wrench set
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up an d then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.
Was this helpful?
Thank you for voting!
No heat in oven
1 person found this instruction helpful.
  • Cynthia from AURORA, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this helpful?
Thank you for voting!
no spark on top burners
2 of 4 people found this instruction helpful.
  • eric from winter haven, FL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.
Was this helpful?
Thank you for voting!
broke the igniter in the oven before I even got the oven installed
1 person found this instruction helpful.
  • june from wills point, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Was this helpful?
Thank you for voting!
Oven was slow to get to temp and not holding temp
1 person found this instruction helpful.
  • Matt from Arlington, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.
Was this helpful?
Thank you for voting!
Burner gas supply connect tubing is cut
1 person found this instruction helpful.
  • Marisa from SAN FRANCISCO, CA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
First remove the burner head by turning counter clockwise to unlock. Use pier to remove the wires from the igniter and burner. Once both burners heads are removed from 1 side, use screwdriver to remove both screws that is holding the burner orifice fitting assembly. You want to repeat the process for the other side. Once both sides ar e done, you can lift the range cover to gain access to the broken burner orifice fitting assembly. Use adjustable wrench to unscrew the two nuts that are holding the assembly in. Remove assembly and replace with new. Reverse the disassembly process then you are done.
Was this helpful?
Thank you for voting!
The broiler would not lite at all and the oven would lite occasionally but would not maintain temperature.
1 of 2 people found this instruction helpful.
  • Vincent from Lewes, DE
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I replaced the igniter in both the oven and the broiler. This was my first time ever working on a range.
I removed the oven door for easy access. To replace the oven igniter, I took the bottom floor out of the oven. The igniter is readily visible at the rear of the burner. I removed the two screws holding the igniter with a socket wrench. The screws were somewhat stubborn but yielded rather quickly. I gently pulled the two wires attached to the igniter from the back of the oven until the connector was exposed. I disconnected the old igniter and connected the new one. Then I simply reversed the the procedure, tucking the connector and wire back through the hole it came from and re - installed the two screws in the bracket. The insulation provided with the kit was used to plug the hole in the back of the oven.

To replace the broiler igniter, I essentially followed the same procedure. However, I chose not to remove the broiler baffle. This made it more difficult to both remove and re-install the two screws holding the ignitor. Otherwise, everything else went smoothly. If I had to do it again, I'd remove the baffle.
Was this helpful?
Thank you for voting!
burners would not light
2 of 5 people found this instruction helpful.
  • michael from Dallas, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers
replace burner-had to hit old burn with rubber mallet to break off grease and took old burner off-two wires were connected to it..put those on new burner and was done--have a little problem--flame is lower now than it was-but it turns on
Was this helpful?
Thank you for voting!
Replacement of igniter
1 of 2 people found this instruction helpful.
  • Robert from Orange, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.
Was this helpful?
Thank you for voting!
Oven making whooshing sound and not heating up
1 of 2 people found this instruction helpful.
  • Jason from Williamsburg, VA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!
Was this helpful?
Thank you for voting!
oven would not light
1 of 2 people found this instruction helpful.
  • mark from fredericksburg, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
replaced the igniter in oven
Was this helpful?
Thank you for voting!
smell gas on oven start up
1 of 2 people found this instruction helpful.
  • Wayne from Long Grove, IL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
took oven tray out and loosened igniter and replace same works great.
Was this helpful?
Thank you for voting!
oven would not light , smell of gas
1 of 2 people found this instruction helpful.
  • jerry from staten island, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
removed oven floor, removed two screws in element . pulled out element wires, secured them so they would not fall back into slot, snaped in new element . scewed it in place , replaced floor . thanks partselect.com
Was this helpful?
Thank you for voting!
smell gas and sometimes a whoof on ignition
1 of 2 people found this instruction helpful.
  • Maynard from Knox, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the flame baffle , removed the two screws that held the ignitor. Then I pulled the wires thru the back wall and disconnected . I had to cut the the connector and install with wire nuts because connector was different. Works fine now .
Was this helpful?
Thank you for voting!
All Instructions for the 3115
91 - 105 of 304