3100P Magic Chef Range - Instructions

Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.

replaced the igniter in oven

took oven tray out and loosened igniter and replace same works great.

I removed the flame baffle , removed the two screws that held the ignitor. Then I pulled the wires thru the back wall and disconnected . I had to cut the the connector and install with wire nuts because connector was different. Works fine now .

Same as the other entries in this section.
The only thing I would add is a hint for removing the broiler igniter. As you can see from the oven igniter, the wires connect with a plug. For the top igniter, the broiler, the plug goes through the insulation and then through a hole in the rear panel of the oven. So, when you pull on it, y ... Read more ou will think it is stuck or the wire is pulled taut. That is because the plug hangs up on the rear panel.
Stick your finger through the square hole that you can see inside the oven, and follow the wire through the insulation. You will feel the small round hole in the back. You have to wiggle the wire up and around a bit to get the plug to fit through the hole. Then you will have the slack you need to change the plugs.
That way, you don't have to pull the whole oven out and break all the caulking seals.

removed oven floor, removed two screws in element . pulled out element wires, secured them so they would not fall back into slot, snaped in new element . scewed it in place , replaced floor . thanks partselect.com

Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!

I replaced the igniter in both the oven and the broiler. This was my first time ever working on a range.
I removed the oven door for easy access. To replace the oven igniter, I took the bottom floor out of the oven. The igniter is readily visible at the rear of the burner. I removed the two screws holding the igniter with a socket ... Read more wrench. The screws were somewhat stubborn but yielded rather quickly. I gently pulled the two wires attached to the igniter from the back of the oven until the connector was exposed. I disconnected the old igniter and connected the new one. Then I simply reversed the the procedure, tucking the connector and wire back through the hole it came from and re - installed the two screws in the bracket. The insulation provided with the kit was used to plug the hole in the back of the oven.

To replace the broiler igniter, I essentially followed the same procedure. However, I chose not to remove the broiler baffle. This made it more difficult to both remove and re-install the two screws holding the ignitor. Otherwise, everything else went smoothly. If I had to do it again, I'd remove the baffle.

Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.

The igniter was located in the bottom of the stove or broiler section. It was hard to get at, but with a little trial and error I figured out how to take the plate between the oven and broiler. Now the igniter was easily accessable. 2 screws on the igniter bracket, then simply unplug the electrical. The igniter supplied had the identi ... Read more cal electrical plug (plug and play). The new igniter works like a charm-oven ignites in about 15 seconds. Piece of cake!!!!!

I read all the reports on your site pertaining to oven igniters and decided to order one. I was amazed when it arrived the next day. I got a lot of tips reading others replys so I lifted off the oven door, took out the racks, removed the 2 screws holding the old igniter and tried to pull it out. There was hardly any slack in the wires, so ... Read more I pulled the stove away from the wall, took off a breadpan size cover in back and found the wires were zip tied to a tube. I cut the tie and unplugged the wires, but the new plug didn't match so I cut the new plug off and rejoined the wires with butt to butt crimp connecters, which I prefer to wire nuts. I used the insulation and new cover from your kit as my old part had the long ceramic insulator and put it all back together. It works like new again and saved me a lot of money. I am very pleased with your product and service, thanks.

Inserting two stove valve knobs took 10 seconds! No tools necessary.

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..

I noticed that the ignitor would glow but the stove wouldn't light - I got the model number of the stove and googled the maytag model number. Came upon your website and realized that 94% of the time the problem was the amps were not enough to light the stove. I looked at all of the stories on how easy it was to fix. I ordered the pa ... Read more rt and received it within 3 days. I opened the door part way and lifted it straight up to remove it. I pulled out the bottom broiler plate by grabbing the back on pulling up. I undscrewed the wing nut of the flame bar and had easy access to the igniter. I removed the two nuts from the old igniter. Unplugged the igniter from the easy access door from the back and plugged in the new igniter. Replaced the access door and attached the igniter with the two nuts. Put the flame bar back on, put the broiler plate back on, put the door back on, plugged in the stove turned it on and success. It was so easy. I know in our area I would have paid near $200 for a service technician to come out and do what I did in approx. 20 Minutes and $50 for the part. Thank you so much for you website to help us not so talented appliance repair homeowners.