31001 - Instructions

Step1: Remove oven door. Open oven door about 3-4 inches and pull up with 2 hands.

Step2: Turn oven light ON so you can see.

Step3: Remove bottom tray by pulling on the 2 rear clips and lift tray up and out of the oven.

Step4: Using a nut driver remove the 2 nuts holding the ignitor in place. If nuts are ... Read more rusted from heat spray a tiny bit of WD-40 on them and totally wipe off any excess when finished removing the nuts.

Step5:Pull wire from old ignitor through the insulation and unplug it from its connection.

Step6: Plug in new ignitor and push it back through the insulation and fasten it back in position with the 2 nuts.

Step7: Re-install bottom tray and door and CONGRATULATIONS cause you just saved yourself about $150! by DIY And you never again will be eating semi-raw chicken or better yet, take the money you just saved and treat yourself and your family to a sushi dinner.

I would like to thank Partselect.com for their quick delivery and very reasonable price on the Ignitor I purchased.

Regards.

first of all i have one advantage even though i am 70 yrs old i had a appliance shop for sears in the 60s and 70s and have not forgotten to much of the basics i am still in the security business and up on electronics. last time i had the company repair the oven , 70 dollars for the part 75 dollars for the svs call. (first igniter was ... Read more on full warranty) well this time i decided to look for trhe part myself, i just went on line typed in oven repair parts and eventually all these sites came up. yours was the most professional looking and i took a chance. guess what everything you promised you delivered. price quality USA made parts and delivered in three days . opened package went to work less than fifteen minutes back in business.
will sure use you again if the need arises thank you

Pulled off the oven door, just lift straight up. Pulled out the floor of the oven, very easy just lift from the back. The only problem I had was the screws holding the old igniter wouldn't come out, they just spun. I snipped them off and picked up two new ones at the hardware store. Pull the wiring harness in through the hole in the b ... Read more ack of the oven. Unsnap old wiring harness, snap in new one. Reattach the new igniter, replace floor, replace door. Turn on oven and cook food... fairly easy repair.

I first removed the bottom of the oven and the flame guide to uncover the igniter assembly. Then I applied WD40 to the two Philip head screws and unscrewed them to release the old igniter. The two wire leads from the igniter went into the back of the oven and I could not reach the connection block. So I pulled the oven out far enough to g ... Read more et behind it and took off the panel covering the electrical wires in back. I had previously disconnected the electrical cord from the wall outlet. After I determined that I could not remove the connection block I returned to the igniter and cut the two existing wires close to the ceramic igniter assembly. I marked the top wire with a Sharpie pen so that I would not mix up the new leads when I install the new igniter. Although it was awkward to work inside the small oven space I was able to strip the insulation back about 1/2 inch and then connect the new igniter wires using the twist caps supplied with the kit. I pushed the wires back into the space and added the insulating material supplied. The igniter assembly was then installed with the original two screws and the other oven covers and flame guide reinstalled easily. After reconnecting the power outlet the oven was back in operation with ignition of gas flame within a minute or so. It was a good feeling and now we do not need to consider replacing the gas range.

Range is 20+ year old 'condo issue' and difficult to pull from wall since previous owner had tiled it in. Going in from the back was going to be a pain.
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws hol ... Read more ding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!

I realized where the ignitor was and I turned off the circuit breaker took the v plate off with a little tie nut unscrewed the 2 small nuts and small plate to hold wires in and pulled the pig tail wire out and unplugged it and then took new one and installed it in reverse order done in 7 minutes thanks michael

The bottom burner would not stay lit. I determined that it was as a result of the ignitor's voltage droping. The thing still glowed red but apparently the voltage drops and closes the gas valve. So, I switched the broiler one with the bottom one to see if it would work. It did. Then I bought the new ignitor and put it in where I had t ... Read more aken the broiler ignitor out. You have to take care to put the insulation back and shove the connector well into the hole so that there is no possibllity of it melting. I also replaced the oven top. I had bought that part a couple of years ago because I had dropped some things on it and it was chipped. When I got the top I thought it would be somewhat intuitive as to how to replace it. But, it wasn't. So,it stayed in its box. When I had the other problem I decided to tackle the top too. First turn off the gas and unplug the oven. You have to pry the top off with a screw driver. Then, you disconnect wires which run to the ignitor for each burner. You also have to disconnect the gas lines running to each dial. Now, you take the top off. To get the burners off the top you have to take a pair of channel locks and open them wide, wrap a rag around the burner and turn them like screws. Under the top there is an assembly that holds the gas lines in place. that has to be removed from under each buner. These assemblies are not interchangeable!!! One is left and the other is right. You then reverse everything. Put the burners in by screwing them down. Its hard but if you put a rag over them you can strike them with a rubber mallet. Screw the gas line assemblies into the bottom of the top. Then hook up the wires and then the gas lines. Then, you pop the top back in. There are those pressure clamps that hold the top down. I made a mistake with the gas line assemblies and switched them. So, when I tested the repair I realized I had the front dial controlling the rear burners and vice versa. Some day I take it all apart and fix it again!

Opened the box and took out the black color grates~~removed discolored grates and put the new ones on. Looks like a brand new stove and much nicer to look at as it is the first thing you see when you enter the kitchen.

removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.

I took the oven bottom out and then removed the screws that cover the safety valve, then I pulled the oven out and undid the safety valve in the rear of the oven. This was all accomplished with the electricity off and the propane also turned off. I then reinstalled the safety valve.

It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.

First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !

Remove the oven racks. Slide the two catches, located at each rear corner of the oven bottom, toward the front of the oven.

Lift the rear edge of the oven bottom slightly, then slide it back until the front edge of the oven bottom clears the oven front frame. Remove oven bottom from oven.

Pulled storage drawer out to ... Read more the first stop position. Lift up front of drawer and pull to the second stop position.
Grasp sides and lift up and out.

Under storage area, I removed two screws to remove a steel plate. In the oven, I removed two screws that held on the Oven Igniter. Unplugged the Igniter under the storage area.

Plugged in the new Oven Igniter, replace the two screws that held the Oven Igniter, replace the two screws for the steel plate. Put the storage drawer back, the bottom of the oven back and the racks.

It was easier than I though it would be.

The repair was easy. Partselect processed my order quickly and my part was delivered sooner than I expected.

Removing the old igniter was simple. I took off the oven door to create easy access to the oven. I then unplugged the connection and removed the screws that held the older igniter in place. Installing the new ignit ... Read more er was almost as easy. I followed the same steps as above, but in reverse. I accidentally dropped one of the screws, so installation probably took 1 minute longer than removal. :)

I'm a very satisfied customer.

Lifted the top up, only a few inches as the possibality of kinking the gas line was a issue. Took two screws out and replaced the unit, threaded the thermostat down through the oven. It was a breeze. I am 68 year old woman and did I myself.
Most importantly, the process of getting the part was amazing, ordered it in the AM and receiv ... Read more ed it the next day (no extra charge)and by miday the range was good as new. Great service!