31-33 Tappan Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
A mouse living in my stove!
15 of 20 people
found this instruction helpful.
-
Amy from Hughestown, PA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
One night I found a mouse living in my stove. We found it literally living underneath the top of the stove (the part where the burners are that you have to lift up). The insulation on the inside of the stove was literally covered with mouse poop, dog food, dog treats, and scraps of food among other things. It was totally nasty and I thoug
... Read more
ht we would have to buy a new stove. However, I searched online and found replacement insulation on PartSelects website and ordered it. It was cheap and the fix was removing old insulation, vaccuming out and cleaning the stove then replacing the insulation with the new one. PartSelect had a great price and shipped promptly.
Read less
Was this helpful?
Thank you for voting!
burner wont heat all of the time
14 of 17 people
found this instruction helpful.
-
Daivid from North Attleboro, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed old terminal block . cut wires and spliced new terminal block and insulated with shrink wrap. Very eazy
Other Parts Used:
Was this helpful?
Thank you for voting!
Element caught fire when i preheated my oven
19 of 33 people
found this instruction helpful.
-
Michael from Union City, TN
- Really Easy
- Less than 15 mins
I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on
... Read more
button and now I'm back in business.
Read less
Was this helpful?
Thank you for voting!
burner wouldnt heat
11 of 13 people
found this instruction helpful.
-
Doug from Ashton, IA
- Really Easy
- 15 - 30 mins
removed element , cut wires, conected wires,replaced element
Was this helpful?
Thank you for voting!
Broiler element burned out
10 of 11 people
found this instruction helpful.
-
Merlin from Newport News, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Very important first step: Turn off the circuit breaker for the range or disconnect the power cord.
I removed the oven door to make it easier to access the back of the oven; remove two screws and the door lifts off of the brackets. Removed a screw from the top of the oven that secures one end of a wire that supports the broil eleme ... Read more nt. Removed two screws that secure the broil element plate to the back of the oven. Pulled the element forward exposing the end terminals and wires. The wires are connected to the element by spade connectors. Used long nosed pliers to remove the connectors from the element. Pushed the connectors on to the new element and stuffed the ends of the element and wires back through the opening and the insulation. Reinstalled the two screws holding the element in place and the screw holding the wire in place across the top of the oven. Reinstalled the door. Took less than 30 minutes.
I removed the oven door to make it easier to access the back of the oven; remove two screws and the door lifts off of the brackets. Removed a screw from the top of the oven that secures one end of a wire that supports the broil eleme ... Read more nt. Removed two screws that secure the broil element plate to the back of the oven. Pulled the element forward exposing the end terminals and wires. The wires are connected to the element by spade connectors. Used long nosed pliers to remove the connectors from the element. Pushed the connectors on to the new element and stuffed the ends of the element and wires back through the opening and the insulation. Reinstalled the two screws holding the element in place and the screw holding the wire in place across the top of the oven. Reinstalled the door. Took less than 30 minutes.
Read less
Was this helpful?
Thank you for voting!
Replacement bowels didn’t fit
10 of 11 people
found this instruction helpful.
-
Russell from ROEBUCK, SC
- Really Easy
- Less than 15 mins
Pulled the heating elements out took the bowels out that didn’t fit, threw them away and replaced them with the perfectly fitting bowels from this site and replaced the heating elements.
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven Racks needed to be replaced.
11 of 14 people
found this instruction helpful.
-
Peter from Chicago, IL
- Really Easy
- Less than 15 mins
Slide out the old; slide in the new!
Was this helpful?
Thank you for voting!
wiring was burnt off to burner
12 of 19 people
found this instruction helpful.
-
Margaret from Portage "BlueKnob", PA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The range, (1988 Tappan) was givin to the church by one of our members. While using it, --after a period of time-- the wire burnt off to one of the burners. Since the couple gave us a brand new top for the stove that was still in the box, we decided to fix the stove up.
Now, with new wiring to all four burners, new shiney drip pans ... Read more and,,,,a new top, we have a very new looking stove for in our church kitchen.
The parts I ordered from PartsSelect, came in just a few days of placing the order,
This is one site that I have wrote down in my address book for any future parts to items we may need.
Now, with new wiring to all four burners, new shiney drip pans ... Read more and,,,,a new top, we have a very new looking stove for in our church kitchen.
The parts I ordered from PartsSelect, came in just a few days of placing the order,
This is one site that I have wrote down in my address book for any future parts to items we may need.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Bake Element Stopped Working
11 of 16 people
found this instruction helpful.
-
Meaghan from HOLLY HILL, FL
- Very Easy
- Less than 15 mins
-
Screw drivers
When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!
Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove bakin ... Read more g racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!
Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove bakin ... Read more g racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!
Read less
Was this helpful?
Thank you for voting!
Draw Glide Broken Off Bottom Drawer.
9 of 11 people
found this instruction helpful.
-
Kathleen from fall river, MA
- Really Easy
- Less than 15 mins
New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.
Was this helpful?
Thank you for voting!
Old switch killed by a short between wires
9 of 12 people
found this instruction helpful.
-
Darren from San Diego, CA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Turn off the electricity
Remove knob
Unscrew old switch
Lift stovetop & prop
Remove wires from switch
Remove switch
Plug wires onto new switch
Put new switch in place
Shut stovetop
Screw new switch in place
Trim knob post
Put adapter on post
Put knob back on
Turn electricity ... Read more back on
Cook dinner :)
Remove knob
Unscrew old switch
Lift stovetop & prop
Remove wires from switch
Remove switch
Plug wires onto new switch
Put new switch in place
Shut stovetop
Screw new switch in place
Trim knob post
Put adapter on post
Put knob back on
Turn electricity ... Read more back on
Cook dinner :)
Read less
Was this helpful?
Thank you for voting!
Electric burner switch shorted out.
9 of 12 people
found this instruction helpful.
-
Armando G from Alice, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connec
... Read more
t them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.
Read less
Was this helpful?
Thank you for voting!
My element had a hole in it
8 of 10 people
found this instruction helpful.
-
Kathy from Gentry, AR
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed old elements I stalled new ones
Other Parts Used:
Was this helpful?
Thank you for voting!
terminal block kit needed for two burners
7 of 7 people
found this instruction helpful.
-
Geraldine from MT HOOD PRKDL, OR
- Very Easy
- 15 - 30 mins
-
Screw drivers
It was either fix the terminal blocks or buy a new stove. Our appliance man told us how we could do this ourselves and sent us a link. In the meantime I'd found yours, which was quite a bit cheaper and it too, came with a How To Video. Very easy!! All the parts fit and work beautifully and all for under a hundred dollars! We replaced two
... Read more
terminal block, one element and all 4 drip bowls! Nice friendly service!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Large burner wouldn't heat
15 of 31 people
found this instruction helpful.
-
Phyllis from Elberon, IA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.
Was this helpful?
Thank you for voting!