EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

31-252 - Instructions

All Instructions for the 31-252
46 - 60 of 327

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
OLD STOVETOP COILS
6 of 6 people found this instruction helpful.
  • SANDY from TOMAH, WI
  • Very Easy
  • Less than 15 mins
LOOKED FOR MODEL# OF STOVE.. ENTERED MODEL # IN PARTS.COM SEARCH.
MATCHED COIL AND DRIP PANS
ITEM NUMBERS AND SIZE.
PLACED ORDER.
ARRIVED FOLLOWING WEEK WELL PACKED.
PULLED OUT OLD COILS/DRIP PANS.
PLACE *NEW* DRIP PANS IN FIRST. THEN PUSH IN *NEW* COILS
**NO PAID INVOICE WAS RECEIVED**
We d4/24/2024
Was this helpful?
Thank you for voting!
Surface element didn't work
6 of 6 people found this instruction helpful.
  • chris from DEWEY BEACH, DE
  • Very Easy
  • Less than 15 mins
Make sure whichever surface element you are to replace is OFF.Carefully remove surface element by pulling it out of socket and remove drip bowl. Cleaned area around range top and place new or old drip bowl in place. Line up drip bowl cutouts and place on range top and simply push in/plug (2 prongs)in new surface element and place on drip bowl. It's that easy! To install 2 new surface elements and drip bowls took less than 5 minutes.
Was this helpful?
Thank you for voting!
Element burned out
6 of 7 people found this instruction helpful.
  • James from Colonial Beach, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The I reversed the process to install the new element which was exactly the same as the burned out one.
At first I was on the verge of replacing the whole stove before I decided to google " ra nge heating elements". I ordered the part from your company and it arrived promptly.
Needless to say, I am thrilled that I don't have to buy a new stove. This one now works perfectly!
Was this helpful?
Thank you for voting!
The elements were not heating up
6 of 8 people found this instruction helpful.
  • Tanya from KALISPELL, MT
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!
Was this helpful?
Thank you for voting!
Push button oven light switch broke and fell inside the console.
5 of 6 people found this instruction helpful.
  • Daniel from Evansdale, IA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Determined how to proceed to disassemble the console. Unplugged the power cord, shut off the gas valve, removed six philips head screws from back panel and one philips head screw from side panel that held the front glass cover in place. Removed the nut off of the old switch body and the two oven control knobs and the timer/clock knob. Rem oved the front glass by pulling the right side forward and sliding it slightly to the right. Disconnected the two wires from the back of the old switch.Removed the nut holding the old switch body to the console frame. Replaced with the new switch and did a reassembly by backtracking my steps. I even remembered to clean both sides of the control console glass before reinstalling it. Placed the range back in position, checked it for level, plugged the power cord in and checked for the proper operation of the new switch, turned on the gas and checked for any possible leaks from moving the range. The switch was a perfect match. The picture on the grid paper background really helped in identifying the switch that I needed.
Was this helpful?
Thank you for voting!
Glides broke on lower storage drawer
5 of 6 people found this instruction helpful.
  • James from WEST BEND, WI
  • Really Easy
  • Less than 15 mins
The front glides easily snap into a hole on the sides of the range. The rear glides easily snap onto the sides of the lower rear of the drawer.
Was this helpful?
Thank you for voting!
Refrigerator Light bulb went out
7 of 12 people found this instruction helpful.
  • ANGELA from MEBANE, NC
  • Very Easy
  • Less than 15 mins
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this helpful?
Thank you for voting!
Couldn't find replacement trays locally. Part Select was very helpful and prompt in shipping.
5 of 7 people found this instruction helpful.
  • Rosemary from St. Albans, ME
  • Really Easy
  • Less than 15 mins
Just placed the chrome bowl trays in place and was good to go. They look very nice.
Was this helpful?
Thank you for voting!
Burning electrical smell and "buzzing"
5 of 7 people found this instruction helpful.
  • Louis from Beloit, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
I started to smell burning electrical smell from the burner area and heard a "buzzing" sound from the burner control while the burner was on. Pulled the element and noticed that the wire coil end of the left element was burned and pitted from arcing.
Pulled the range top up, used a phillips screwdriver to remove the terminal block clip from the range top. Upon inspecting the burner terminal block, I saw the brass wiper was missing from one side of the left slot, and there was considerable heat damage around the slot opening.
The terminal block being replaced was already replaced earlier for the same problem. The appliance repair folks recommended that we use light cookware on the burner. Instead, ensure both element leads are fully inserted into the terminal block.
I turned the power off at the breaker, used a utility knife to carefully slit the heat shrink tubing on the existing replacement, unscrewed the ceramic wirenuts, removed the old block, straightened out the range wires, slid the new heatshrink over the range wires, then twisted the new terminal block wires to the range wires. Screwed on the ceramic wirenuts, slid the heatshrink tubing over the wirenuts, and used matches to shrink it tight.
The package contains an instruction sheet with simple instructions.
Once the new terminal block was installed and the element terminals were fully seated, the "buzzing" from the burner control disappeared.
Was this helpful?
Thank you for voting!
I damaged surface element left kettle on without water in it
4 of 4 people found this instruction helpful.
  • Kenneth from LANOKA HARBOR, NJ
  • Really Easy
  • Less than 15 mins
The repair was really easy. All I did was unplug the surface element and plug in the new one.
Was this helpful?
Thank you for voting!
replaced four surface elements
4 of 4 people found this instruction helpful.
  • RICHARD from HOUSTON, TX
  • Really Easy
  • Less than 15 mins
Pulled out the existing surface elements (4) and inserted the four new ones. New surface elements work great. Heats like a new cooktop stove.
Was this helpful?
Thank you for voting!
Switching out drip pan, surface element and glide door
4 of 5 people found this instruction helpful.
  • Carrie from SEMINOLE, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
i used a screwdriver to remove the old drip pans and broken surface element in addition to prepping the bracket for the door. It was extremely difficult for me to find these parts for the frigidaire oven but these fit perfectly! I was extremely pleased with how quick it was to replace or fix everything. I will definitely order again when the other surface elements go!
Was this helpful?
Thank you for voting!
Front left burner would not shut off, then switch fried
5 of 8 people found this instruction helpful.
  • connie from madison, NC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Unplug range, remove top back panel. Remove knob. Replacement part is different, but if you look closely, each metal tab has a number stamped on the plastic housing directly beneth it. Remove old switch (2 screws)and remove and replace wires one at a time. You will need to cut the "one size fits all" metal shaft that the knob attaches to. We had to remove most of it, leaving only 2 "segments". File rough edges and apply vaseline so that the plastic sleeve will slip right on. We used the shorter sleeve (only 2 that are supplied will fit the knob). Replace unit and screw in. Replace knob.
Was this helpful?
Thank you for voting!
Switches were going bad and making a popping sound and smoking.
4 of 5 people found this instruction helpful.
  • Joshua from Homestead, FL
  • Easy
  • 30 - 60 mins
  • Screw drivers
Pulled out the range, unplugged it and removed the upper back panel. The switches were held in place with two screws. Removed the old switches, detached the wires and plugged them into the new switches. Mounted the new switches, replaced the back panel, plugged the range back in and pushed it back into position. Appliance repair compa ny wanted $370. I did it in 45 min. for less than $100.
Was this helpful?
Thank you for voting!
Coroded drip pans
4 of 5 people found this instruction helpful.
  • Lori from Old Town, FL
  • Really Easy
  • Less than 15 mins
Removed heating elements and replaced drip pans. And by the way, this is the only 'pans' I could find to fit. Thanks.
Was this helpful?
Thank you for voting!
All Instructions for the 31-252
46 - 60 of 327