30560C Murray Lawn Mower - Parts

This bolt is designed for use with various models of lawn and garden equipment and is a genuine OEM part. Featuring a square securing-area underneath the head for locking purposes, this bolt measures .31-inches in diameter and is 18 threads-per-inch. This bolt is made of high-quality metal and may require you to acquire multiple, depending on the use and location of installation for your equipment.

This is an authentic Murray replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers. The metal washer is used to provide spacing between the steering spindle and the front axle assembly. This item is sold individually, please note two washers may be needed.

It is an authentic high quality hardware that is supplied from original equipment manufactured for use with Murray lawn tractors. This cotter pin fits through the axle helping to secure the mower wheel. Please note one durable metal pin is included per order. You will need pliers to install or remove this item.

This hex bolt is sourced from the original equipment manufacturer. The bolt is designed to fasten two individual parts together in your lawn and outdoor equipment. It is made of steel to withstand harsh environmental conditions and measures 0.25 inches in diameter and 0.62 inches in length. The hex bolt gets its name from its hexagon-shap...Read moreed head, which makes it easy to grip with a wrench or socket. Before installing the new bolt, first clean the threaded hole where the bolt rests to remove any dirt or debris in the area. Once the area is clean you can place the bolt in position using your hands and tighten it using a wrench or socket. It is important not to overtighten as this could damage the area and the bolt. Sold individually.

This hex center lock nut is sourced from the original manufacturer for use in lawn and garden power equipment. It is a hexagon-shaped fastener for bolts/studs that is responsible for the keeping the bolt/studs secure during use. The nut is made of metal and has a diameter of 5/16 of an inch and a thread pitch of 18 internal threads per in...Read morech. Over time the threads in the nut can wear down and the nut itself may crack or break. It is important to replace it as soon as necessary to avoid damaging your equipment. Use a socket or wrench to remove the old nut and thread the new one on. Make sure to order the correct number of nuts for your equipment as each nut is sold individually.

This Washer (.40.81 16g Flt) is a black, metal part, requiring a socket set to install. Installation is rated as "Easy". This washer can be used to provide a tight fit between connected components. It attaches onto the bell crank between the adjusting nut and cotter pin. Refer to your make, model and diagrams to check if this model is right for you.

The retainer attaches to the idler arm support. This genuine item is supplied by the original equipment manufacturer for use with tractors and rear engine riders made by Snapper, Murray, and Simplicity. It is made out of metal and is sold individually. During the installation process, a wrench set might be needed to replace this part. Over time this part may break and will need to be replaced.

This light bulb is an authentic OEM replacement part supplied by Murray. It is compatible with over 150 models of lawn tractors. This bulb allows the tractor to produce light. This part is made of metal and glass. It should be replaced if it is cracked or broken. No tools are required to replace it. Discard the old bulb immediately, and wear work gloves to protect your hands when handling broken glass.

This item is sourced directly from the original equipment manufacturer. It is specially designed for use with Murray garden tractors. The idler pulley helps to apply tension on the belt. Over time it may wear out or get damaged eventually requiring a replacement. It is made of high-quality material and is sold individually. Check the diag...Read morerams of your model for the exact location and the correct installation of this part. You will need a wrench to remove and secure the hardware that holds the idler pulley.

Ring,snap.625d.035t

This is an authentic Murray replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers. The e-ring is used to retain the washer on the wheel\\\'s transaxle assembly. This item is available as an individual replacement part.

This is an OEM Murray part directly sourced from the manufacturer for lawn tractors. It wraps around the drive pulley and the stack pulley assembly and helps to rotate both parts. Pliers may be needed to replace this part if it becomes broken or stretched. This 30" belt is priced individually.