30112 - Parts

This OEM plug is sold individually and measures just over an inch in diameter. It attaches to the case cove of your equipment, is black in color, made of plastic and will need to be replaced when the old plug is dry out, cracking, or generally showing signs of wear. You may observe grease leaking out if this part needs replacing. Dirt c...Read morean also get into the case if it is cracked, and cause problems over time such as a grinding noise. This is a somewhat challenging repair that requires a screwdriver, pliers, and a wrench.

This replacement switch is a genuine OEM part, not an aftermarket equivalent. It is supplied directly from original equipment manufacturer for Murray riding lawn mowers and tractors. This switch is secured under the seat to prevent the engine from running without a driver in a seat. Mechanical switches over time tend to wear out requiring replacement. Please note, this plastic switch is sold individually.

Switch push button no/nc snap-in

Retainer, ring, 3/4

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

This 1/4-20 x 3/4-inch hex-head screw secures parts on compatible outdoor power equipment. It is made from Grade 5 steel and has a yellow zinc finish for added rust resistance. Check the equipment model and parts diagram before ordering.

This is a genuine manufacturer-approved part which is made for use with Murray and Snapper riding lawn mowers and garden tractors. It is one of the special bushings that are utilized on the equipment. This part acts as a lining for components helping to provide a tight fit. Make sure to check the appropriate diagrams of your model for the...Read more correct application of this hardware. It is made of durable material and is sold individually. You may need a screwdriver and pliers to replace it.

This O-ring, also known as a round seal, is an authentic OEM part used in lawn and garden equipment. It is a small, circular, rubber ring that helps create an airtight seal between the oil filter filler and engine to prevent leaking and ensure adequate lubrication. It is common for the O-ring to become brittle and lose its elasticity due ...Read moreto aging, and exposure to chemicals and high temperatures in the equipment. If an O-ring fails, it can result in oil leakage, leading to reduced equipment performance, and potential damage to the surrounding components. Carefully the oil ring off the sealing surface and clean the area thoroughly to ensure a proper seal for the new O-ring. Lightly lubricate the new O-ring and press it on to the sealing surface.

This is a genuine manufacturer supplied replacement fuel filter. It is specially produced for use with Toro snowthrowers. This is a plastic fuel filter that is sold individually. Its purpose is to filter out any contaminants from the fuel before it goes into the engine. It will over time get clogged and restrict the fuel from getting to t...Read morehe engine. To replace this filter you should only need pliers to remove and install the clamps that secure fuel lines.

This thrust washer is an authentic item which is supplied by the original manufacturer for Murray and Snapper lawn mowers. It is a special type of washer that will resist torque applied by the bearing while ensuring a tight fit. Over time it may wear out, get damaged or simply lost eventually requiring a replacement. This thrust washer is...Read more made of a durable material and is sold as an individual component. Note, you may need a wrench set to remove and resecure the hardware that holds this part. Check the diagrams of your specific model for the exact location and application.

This replacement ball bearing is an authentic OEM component which is designed for use with Murray and Snapper lawn and garden equipment. Bearings are utilized to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. S...Read moreymptoms of failing bearing may include squealing, screeching, and an entirely new type of "grinding" (usually heard or felt as the motor powers-down). This high-quality component is made of durable metal and is sold as an individual part. A wrench set will be needed to perform this repair. Make sure to refer to the appropriate diagrams for your model to ensure the proper replacement procedure.