30-79 Tappan Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven light bulb went dark; it needed replacing
10 of 17 people
found this instruction helpful.
-
Lise from CEDAR GROVE, NJ
- Very Easy
- Less than 15 mins
Twisted replacement bulb into place easily. Let there be light!
Was this helpful?
Thank you for voting!
error sensor on display when oven was used
8 of 11 people
found this instruction helpful.
-
James from Clarence, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
I looked up the error code on line and found it was likely a faulty oven temp sensor. I was able to find the part and diagram at partselect.com and placed an order. The probe was in stock and arrived within a couple days. The repair took only about 20 minutes and works fine now. Thanks for your help partselect.com!
Jim
Jim
Was this helpful?
Thank you for voting!
Grates were old and rusted and scratching the bottom of my pots
7 of 9 people
found this instruction helpful.
-
Sue Z from Los Angeles, CA
- Really Easy
- Less than 15 mins
I threw the old ones out and replaced them with the new ones. It was a no-brainer :) The parts arrived super fast. Great, no hassle service.
Was this helpful?
Thank you for voting!
Oven racks rusted
11 of 21 people
found this instruction helpful.
-
Wendell from Ocala, FL
- Really Easy
- Less than 15 mins
Ordered new racks and replaced them.
Was this helpful?
Thank you for voting!
Broken Drawer Glide
6 of 6 people
found this instruction helpful.
-
Sharon from Hamlin, NY
- Really Easy
- Less than 15 mins
It snapped right into the drawer, was very easy
Was this helpful?
Thank you for voting!
Ignitor glows but not hot enough to open the gas valve. It's old.
6 of 6 people
found this instruction helpful.
-
Kenneth from MESQUITE, TX
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
My Tappan Tail:
Open the oven and remove the racks, turn on the oven light.
Remove two screws in the back to remove the bottom plate. Mine are about 1 1/4 in. long.
Remove one nut holding the butterfly plate in place. Ignitor will be exposed.
Turn off the oven light and unplug oven. Don't drop the plug behi ... Read more nd the oven, I was ready for that one.
Drop light or flash light will be needed, it's dark in there. And something to sit on, 16" old plastic milk caddy, I just happen to have one.
Remove the two screws holding the ignitor, don't cut the wires just yet. Take note where the wiring runs. Install the new ignitor. My wires went behind the gas piping.
I cut the bottom wire from the old ignitor first, up close to the ceramic. Wire shield can be reused, slide it over the new wire. Cut the old wire, leave a lot. Trim the new wire to desired length and strip the ends of both and use the ceramic cap and connect the wires.
Do the top wire.
Slide the wire shield next to the igniter, adjust the wires so the wire shields won't slide away from ignitor. With the butterfly shield back in place it's time to plug it in and give it a test.
Nice.
Replace the bottom plate of oven, screw holes hard to find. Had to use an awl to find the holes to line up the screws. I also didn't push the front of the plate down into place until I had the screws started. It helped.
You might think this is overkill, but how many of us have ever replaced the ignitor. Not me.
I do a lot of DIY's. I'll rate this as a 1, easy.
What shall I bake first, cornbread of course. I my cast iron skillet.
Open the oven and remove the racks, turn on the oven light.
Remove two screws in the back to remove the bottom plate. Mine are about 1 1/4 in. long.
Remove one nut holding the butterfly plate in place. Ignitor will be exposed.
Turn off the oven light and unplug oven. Don't drop the plug behi ... Read more nd the oven, I was ready for that one.
Drop light or flash light will be needed, it's dark in there. And something to sit on, 16" old plastic milk caddy, I just happen to have one.
Remove the two screws holding the ignitor, don't cut the wires just yet. Take note where the wiring runs. Install the new ignitor. My wires went behind the gas piping.
I cut the bottom wire from the old ignitor first, up close to the ceramic. Wire shield can be reused, slide it over the new wire. Cut the old wire, leave a lot. Trim the new wire to desired length and strip the ends of both and use the ceramic cap and connect the wires.
Do the top wire.
Slide the wire shield next to the igniter, adjust the wires so the wire shields won't slide away from ignitor. With the butterfly shield back in place it's time to plug it in and give it a test.
Nice.
Replace the bottom plate of oven, screw holes hard to find. Had to use an awl to find the holes to line up the screws. I also didn't push the front of the plate down into place until I had the screws started. It helped.
You might think this is overkill, but how many of us have ever replaced the ignitor. Not me.
I do a lot of DIY's. I'll rate this as a 1, easy.
What shall I bake first, cornbread of course. I my cast iron skillet.
Read less
Was this helpful?
Thank you for voting!
broken lens over oven light
11 of 22 people
found this instruction helpful.
-
Leslie from Warsaw, VA
- Really Easy
- Less than 15 mins
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Was this helpful?
Thank you for voting!
one of the burners broke of the assembly and would'nt light anymore.
7 of 11 people
found this instruction helpful.
-
geraldine from belford, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
I went on line looked it up, ordered it, it came within 2 days.
I then removed 2 screws with a philips head screwdriver popped out old one, replaced with new one, put the screws in, turned it on , and it worked!
As a women I was thrilled to do this myself.
I then removed 2 screws with a philips head screwdriver popped out old one, replaced with new one, put the screws in, turned it on , and it worked!
As a women I was thrilled to do this myself.
Was this helpful?
Thank you for voting!
Glides broke on lower storage drawer
5 of 6 people
found this instruction helpful.
-
James from WEST BEND, WI
- Really Easy
- Less than 15 mins
The front glides easily snap into a hole on the sides of the range. The rear glides easily snap onto the sides of the lower rear of the drawer.
Other Parts Used:
Was this helpful?
Thank you for voting!
Refrigerator Light bulb went out
7 of 12 people
found this instruction helpful.
-
ANGELA from MEBANE, NC
- Very Easy
- Less than 15 mins
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this helpful?
Thank you for voting!
Push button oven light switch broke and fell inside the console.
5 of 6 people
found this instruction helpful.
-
Daniel from Evansdale, IA
- Easy
- 15 - 30 mins
-
Screw drivers
Determined how to proceed to disassemble the console. Unplugged the power cord, shut off the gas valve, removed six philips head screws from back panel and one philips head screw from side panel that held the front glass cover in place. Removed the nut off of the old switch body and the two oven control knobs and the timer/clock knob. Rem
... Read more
oved the front glass by pulling the right side forward and sliding it slightly to the right. Disconnected the two wires from the back of the old switch.Removed the nut holding the old switch body to the console frame. Replaced with the new switch and did a reassembly by backtracking my steps. I even remembered to clean both sides of the control console glass before reinstalling it. Placed the range back in position, checked it for level, plugged the power cord in and checked for the proper operation of the new switch, turned on the gas and checked for any possible leaks from moving the range. The switch was a perfect match. The picture on the grid paper background really helped in identifying the switch that I needed.
Read less
Was this helpful?
Thank you for voting!
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
5 of 7 people
found this instruction helpful.
-
Phyllis from GAINESVILLE, GA
- Easy
- Less than 15 mins
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in
... Read more
the house.....I show them what I DID!! :-)
Read less
Was this helpful?
Thank you for voting!
Oven wasn't staying on and or re-lighting, recycling to maintain the set Temp.
4 of 4 people
found this instruction helpful.
-
michael from MILFORD, CT
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Opened the oven door, removed the racks. Removed the bottom cover, two thumb screws in the rear, bottom, of the oven. This exposed the top plate of the burner, (actually in the top of the broiler section) 1 nut took this cover off. Now, the burner and the igniter are exposed. Two screws removed the igniter, and two wires with ceramic wire
... Read more
nuts. Disconnected these two wires and that was it. Installed the new igniter in reverse procedure as above. Pretty easy. Probably should have turned off the power to the Range first just to be safe.
Read less
Was this helpful?
Thank you for voting!
Replace Chrome Drip Pan
4 of 4 people
found this instruction helpful.
-
Mavis from McKees Rocks, PA
- Easy
- Less than 15 mins
No installation steps required. I did have very fast delivery of parts ordered.
Was this helpful?
Thank you for voting!
gas oven won't light
5 of 7 people
found this instruction helpful.
-
James from GRASS VALLEY, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
get liquid wrench, remove oven door(2 screws) remove oven bottom(2 screws) follow directions included with part. unplug or shut off electricity at breaker panel, Have a good light source.
Was this helpful?
Thank you for voting!