30-76 Tappan Range - Instructions

I found your website fast and easy. I needed replacement drip pans fast, ordered them on-line, and received them within 3 days of ordering. Your parts were the best deal, the least shipping charges, and the picture and description on your website was the best. Thanks.

As the previous people stated on similar repairs;
I took the new drip pans out of the box,removed the old grate burners and the old rusty drip pans; then, simply set the new pans in place and replaced the existing grates. This whole process took less than 10 minutes.

An all-purpose hardware-store knob didn't work, the shaft was way too short.With the aid of the Part-Select diagram,I found the correct stove model number. The simple little Tappan oven control knob cost over $30. I checked other appliance part vendors on-line, but found their part descriptions imprecise and equally expensive. I ordered ... Read more the part and it arrived in 2 days and worked perfectly. An appliance store had told me I wouldn't find a retrofit on such an old stove and I would have to buy a new stove!

snapped the old burner out of the snap fixture on the range lid. snapped the new burner into place. done! voila - I created fire!

Opened the box, took out the drip pans and the put them on the stove. Wow -- even a techno-challenged person like myself could do this! I ordered these on a Tues. at 2:00 p.m. and received them on Wednesday -- that is a first so thanks for the fast service and they look great! Was non-existent to find them at local appliance stores in ... Read more the area so thank you for having them.

replaced it

Found replacement drip pans at partselect.com.
Ordered them and received them in 2 days.
installed the new ones and all is well.
Had I known it was this easy, I wouldn't have spent countless hours scrubbing the old pans with Brillo pads. Considering how much I spent on oven cleaner, scouring powder and steel wools pads, it ... Read more was lest costly to just buy new ones. (and they look better too).
Thank you PartSelect.

No major hardware stores had anything close. One visit to you site was all it took. Parts were loose so we removed them and replaced.

Opened box, popped bubble wrap :) put in drip pans. Was great! Having been looking for the correct ones for a couple of years!

No tools were required. All I had to do was lift off the burner grate. I removed the old drip pans. Put the new drip pans in. I then put the burner grates back on. I did this with all four burners. That's all there was to it. Easy as 1-2-3.

We just recently purchased our home. The gas stove top is stainless steel and works great but the drip pans and burner grates were old, worn, and not very attractive looking. So I decided to replace them with new ones to give my stove top a fresh at like new look.
Thank you so much. They worked great.

first I removed the 4 screws holding the cover in place. then I removed the 26" flourescent tube by slowing twisting it free. Then I attemped to buy another one at 6 or 8 stores with no luck. While surfing the web for tappan range replacement bulbs, your web site popped up. Thank god.

Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as t ... Read more his prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.

The foul order was the cause of a "Mummified Rat" that I found on the bottom Left /outside wall of the oven. I first Unplugged the stove and turned off the gas. I removed the grates and the burners. Each burner is held down with two (2) 3/16" screws which makes it a total of eight (8) screws in all. After removing all eight screws, yo ... Read more u can now pop up the burner lid with a putty knife or a large Screw Driver. I used a large screw driver, After removing the "Lid" you will then see the "Insulation Blanket" draped over the oven, to remove this blanket there are two (2) copper wires securing the blanket in place, you'll have to cut these in order to install your New Blanket. Removing the "Blanket " is a "No Brainer" just be cautious and don't snag any of the "Igniter Wires" The "Insulation Blanket" goes on one way, this can be identified by the pre-cuts on the blanket. I started out on the left side of the stove, and had the right side of the "Blanket rolled up. As I tucked the "Blanket" under the "igniter Wires" and slowly and gently feeding it with my left hand till it lines up with the pre-cut and drapes itself into place as you maneuver it down with your hands Now start with the right side by unrolling the "Blanket" and following the same procedure making sure the "Insulation Blanket" is fully extended on both sides of the oven.

took off the front panel where the burner nobs are was very easy