30-3349 Tappan Range - Instructions

I replaced both gas valve and igniter. I removed oven door and bottom of oven for easy access to both. The door slid off easy and the bottom was held by two thumb screws. I removed the gas flare for easy access to igniter & valve. I then removed the igniter & valve using nutdriver, phillips screwdriver and adj wrench. I then followed ... Read more simple instructions supplied for wire connect on igniter and valve. It was a very easy job for a 25 yr old stove. I made the mistake of ordering only the valve and ordered the igniter later. Having both new parts causes the oven to light in about 30 seconds. Im glad I found partselect online. Nh, westerville, oh

Removed lower burner covers and fan cover to access igniter. Unscrewed igniter and pulled out as far as possible. Marked both wires and snipped them. Twisted on wires from new igniter and mounted igniter. Pulled excess wire thru to back of oven and reassembled covers from first step. Last step was to explain to wife that she needs clean i ... Read more n there MUCH better.

followed online instructions

The philip head screws holding the igniters were frozen. Had to cut off heads with dremel cut off tool, then grabed residual screw with vice gripp pliers. Removed screws and mounted new ignighters. Used new hex head bolts. Attached wires per instruction sheet and tested unit. It worked.

Replacing the faulty ignitor would have been simple enough if my arms were a foot longer and the bolts that secured the old ignitor had not been baked on.

With an ample dose of WD40 and some Vise Grips I finally got them broke loose. An Ohm meter can tell you pretty quickly if the old ignitor is bad. My old ignitor measured m ... Read more ore than 1 mega ohm while the new ignitor read only about 346 ohms.

had the gas company do a free inspection.he told me the igniters go bad over time,so i went online with my model #and found a symptom/remedy page at part select.it said replacing the igniter fixed the problem 100% of the time.that gave me confidence and i ordered it,installed it and fixed it for $53.00(the gasman said most plces charged $ ... Read more 250-300 to fix it.i was proud of myself-1st ever oven repair=great job!!! thanks.

1st took out switch from thermostat unit, located right on the other side of where the temperature knob is located (that controls cooking temp of the oven). Had to lift up range cover to get to the thermostat. Tested this switch with a meter and found it was OK. This made me suspect the igniter, so I ordered one.
To install I fi ... Read more rst unplugged oven (to prevent getting shocked) then took off the drawer on the bottom compartment (push in on tabs on rails until they release). Then take out two screws holding igniter. Mark wires with tape so you know which one goes to the upper part of the igniter and which one goes to the lower part. Then cut wires as close to the body of the igniter as you can so that you have plenty of wire to work with. Then hold igniter in about the place it will be mounted and mark the wires on the new igniter where you want to cut them. Leave a little extra so you have wire at a length that is easier to work with. Scrape off 3/8 inch of insulation off the end of each wire and connect the wires with wire nuts. Re-mount igniter. Put drawer back in. Plug oven back in and try the oven. I hope it works. Mine did thanks to God. Take care.

First I'll say the instructions and comments from this site were right on, making it easy. I slid the oven out and unplugged the electric. Opened the door, took out the racks, took out the two thumbscrews at the back bottom and lifted the bottom plate up and out, and lifted off the heat guard plate. I could then see and reach the ignite ... Read more r pretty easily (the flashlight helped). The igniter may have been replaced before because there were already wire nuts on the wires. I unscrewed the two screws using the nutdriver and noted which wire (top or bottom) went to which wire inside. Unscrewed the wire nuts and removed the old igniter. Used the old igniter to determine where to cut and strip the new igniter's wires. Connected the wires of the new igniter using the wire nuts and put the two mounting screws in. Then just put all the other stuff back in (heat guard, bottom plate/two thumbscrews, racks). Plugged it in and started the oven. Got a small amount of "crackly" noise initially (maybe because the igniter was new) but that went away and it's been working fine and quiet since. Very easy (well, perhaps other than being on your knees, leaned into the back of an oven for a couple minutes). Well worth the effort.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I made sure I memorized just how the wires would re-connect with the wirenuts. I then re-assembled everything. Be sure to read all the instructions, especially how to properly install wirenuts. I ... Read more was able to access the wire connections below the oven chamber through the drawer at the bottom of the range. This is an important detail.

My husband was able to easily remove the old part, and replace with the new ignitor. The wires were long, so he took the extra precaution of tying them away from the flame. It took longer to take everything out and put it back together than the actual repair..

took drawer out, removed tin covers, found igniter and removed,snipped off parts to put on new igniter ,wirenutted old to new put back together ,we had ignition! all in all pretty easy job! detailed instructions that came with new part were easy to follow and precice

1. Unplugged power cord.
2. Removed warming drawer and oven shelves and lower plate
3. Removed old wirenuts from back of warming draw space (awkward to reach in to the back).
4. Removed 2 screws holding ignitor in oven - screws in poor shape and were not reuseable.
5. Found next size up sheetmetal screws and installed ... Read more new ignitor.
6. Ran wires down adjacent to gas feed into warming drawer space.
7. Connected with wirenuts supplied with ignitor.
8. Replaced everything.
9. Tested oven and ate some tasty blueberry muffins.

Remove the oven drip pan & burner baffle. unscrew & cut leads to remove old igniter. Splice old leads to new using furnished wire nuts and remount. Job would have been easier with oven door removed, but didnt want to create a new project.

Unplug appliance. Remove the bottom of the oven (2 screws in back of oven bottom), remove burner cover (2 screws in front and nut in center holding burner). Pull out the bottom storage drawer under the oven and unplug both wires from oven Igniter which are located in the back. One wire plugs into the gas valve and the second wire went ... Read more into a connector that was on the lower left. I removed the screw on the back oven wall that held the burner so I could remove the burner for ease of work. Remove two screws holding the old igniter. The two screws holding the igniter to the side of the burner were stripped and they took a little time to remove but I replaced them with two new screws I had in my misc. screw drawer and had no issue. Cut the top wire and splice it onto the top wire of the new igniter using the porcelain wire nuts provided. Do the same with the bottom wire. Re-assemble and plug back in. Everything worked perfectly.

pulled stove out to unplug the electric cord. Took oven door off and removed the bottom panel (2 screws) and then removed the burner (2 screws). took off old igniter ( 2 nut screws). cut wires and stripped the coating to wire to new unit.
Attached new igniter to the burner, and put the burner back in place and replaced the screws ... Read more so unit was stable.
Turned oven on to make sure ingiter was going to light oven, when oven came on, turned oven off and replaced the cover to the burner and the bottom panel in the oven,. Put the oven door back on........
Probably took 45 minutes.
I ordered the part late Friday afternoon, around 3, and the part was here Saturday Afternoon. I was impressed.