2LSR5233BZ1 Whirlpool Washer - Instructions

Replaced pump without disassembling the cabinet or disconnecting motor or any other parts.

Disconnected power, drain, hot and cold water lines. drained lines to pail before taping to top of unit.

Tipped the unit to a 45 Deg. angle, leaning the top side edge onto a stool so that pump presented well at the raised bott ... Read more om edge.

Removed hose clamps at pump suction and discharge ports and drained water into a shallow soaking pan. Kept clamps on hoses to facilitate reinstallation of pump.

Removed spring clamps at front and rear of pump housing.

Wiggled motor shaft away from coupling in pump. This is a friction fit, so no parts removal was required and no parts "come loose" in the process.

Wiggled new pump housing onto the motor shaft after checking square shaft alignment with respect to square female coupling on pump.

Pushed and twisted hose ends onto pump suction and discharge ports, then pulled spring clamps down over hose ends at pump ports.

Reset spring clamps so that they were aligned and square with pump ports. Reconnected power, drain, hot and cold water line connections.

Washer ran as before but without leaks this time.

First, I removed the softner cup from the top of the agitator. Second, I removed the plastic seal by pulling it out. I then used a socket to remove the bolt holding the agitator down. I then removed the agitiator from the machine and seperated the upper and lower agitator by placing my feet on the lower agitator and pulling up. The dog-ea ... Read more rs were in the upper agitaotr section and easy to see and replace. I re-assembled in reverse order. The whole process took less than 30 minutes.

The tub was out of alignment and water fell behind it and onto the floor. My brother-in-law suggested my problem could be the tub balancing spring and when I moved my washing machine, there it was on the ground.
The schematic does not show where it hooks up. So after I did what I thought looked right, the machine still did not wo ... Read more rk properly. Then I replaced the three suspension springs and that didn't solve the problem.
I found a whirlpool "do-it-yourself" repair book at the library and was prepared to tear into the machine. However, I did not have the tub balancing spring in the correct spot at one end. It hooks up from one of the outer bracket to the back of the housing unit along between the legs. There is a hole that had rusted through. I simply drilled a new hole nearby and low and behold it works!
Easy fix - the frustration was with the poor schematic.

First, be sure to take the washer apart properly! The first time I fixed my washer I took it apart the hard way to change the clutch, and believe me it took longer to put it back together!
This time I was replacing both the water inlet valve and the hose leading to the disperser.
First remove the two screws holding down the con ... Read more trol panel. It then flips back and hangs out of the way behind the washer. Then remove the spring-clip holding the rear plate to the body of the washer, one on each side under the control panel.
Next you need to remove the screws holding the body down to the base at the rear of the machine.
I then tipped the body of the washer forward and let it rest on a bucket so I didn't have to take it completely off. Then it is easy to access the hose and the water inlet valve. Shut off the water and remove the supply hoses to the washer. Remove the two screws holding the water inlet valve to the rear of the washer using a nut driver. Next remove the wires to teh inlet valve, making sure to note which one is cold and hot, and which orientation they are. Mine was yellow on top and brown on bottom. Next remove the springs clamps holding the hose on. Replace the hose re-using the same clamps. Replace the water inlet valve reverse the process to re-assemble the washer. Tilt the body back on, put the screws in the base, clamp the back to the body, flip the contorl panel back over and insert the screws. Reattach the water supply lines and you are done!

Repair was simple, after finding the correct part from Partselect. Exact match. Old part out with removal of one bolt, new agitator assembly installed in five minutes. Works great and saved me from buying a new washer. Cost of repair about $80.00, replace washing machine, about $600.00.

I'd noticed for a while that our 15-year-old Kenmore washer was filling slowly, but when it started to take 30 minutes to fill to the "medium" level, I knew something was really wrong. There was plenty of water pressure, so I replaced a hose that was loaded with minerals and cleaned the filter (also clogged with minerals). But that didn' ... Read more t help! So I ordered a new water inlet valve, and replaced that. There's nothing tricky about the repair -- the hardest part is opening and closing the washer, for which I found instructions online. (Even so, it's the most time-consuming part of the project.) The result is the washer now fills as fast as when it was new. Just for fun, I took apart the old valve and expected to find it encrusted with minerals, but it looked fine, so I'm not sure where the actual breakdown was. But since the part only cost $25 -- less than a service call, for sure -- I was very happy to use a half hour of my time and keep the machine going a while longer.

The repair was very easy. The original dial was a poor design and did not hold up to the twisting and finally let loose. The threaded bottom of the dial stayed on the threaded shaft, so it was a simple matter of grabbing it with nose pliers and spinning off. Glue does not work with this type of plastic, I tried instant glue and hot glu ... Read more e. The replacement part was re-designed with a metal threaded center, so when it arrived in the mail, 3 days after online ordering, I spun it onto the shaft and job was complete. While I waited for the new part to arrive, I threaded 2 nuts onto the shaft and tightened them to each other to give me a temporary 'knob' that I could grab with my nose pliers.

Washer is 29 years old. Found that tub spring hooks into a simple (non-reinforced) hole in the base frame, and it had worn the hole through through the edge of the frame (key hole style). Due to age and low cost of parts, ordered all suspension springs, brackets, & pads. Once they arrived, took the tubs out (first time for that), found ... Read more that the suspension pads looked fine, but the wear pads showed a lot of wear and the front one was snapped in the middle, perhaps an after effect of the spring failure. From my lack of attention, initially tried to get front pad into the wrong set of holes, a bad fit; corrected. Simply drilled a near-by hole in the base frame for the tub spring.

While the tubs were out, took them outside and scrubbed them clean. Also cleaned agitator parts using bottle brushes. Followed the PartSelect videos and owner comments for procedures, methods. Found that some miss some important info, but if you watch others you can combine the info to find what you need re disassembly/assembly.

At one point while attempting to remove the outer tub, did not realize that the screw that holds the rear spring bracket to the tub also holds the tub to the suspension plate.

Took me most of a day for the whole process, and I ended up with pulled/spasmic muscles from all the bending over, mostly from cleaning parts I think. Very helpful to have the parts breakout drawings, videos, others' experience.

Unbalanced load was creating a knocking sound (as if the clothes load was unbalanced). Dismantled the washer to find that one brackets had rusted out. [FYI: 3 bracket at 120 degree apart (for the 360 degree circle)]. I found that the hole (on the bracket) where the spring holds was gone. Purchased parts. Replaced them (spring, bracket, sc ... Read more rew). Reassembled washer then ran wash for a cycle. Successful fix.

Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, the ... Read more n used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.

Removed softner dispenser, removed bolt on top of agitater,replaced parts supplied with repair kit.
Directions were inclosed in package that were easy to follow.I ordered Thrust spacer not knowing it was included in repair kit.

I WAS VERY PLEASED WITH YOUR WEB SITE AND DELIVERY TIME.

Unplugged power cord and disconnected water lines; note which is hot/cold. Washer was then tipped on its front. Discharge hose was disconnected. Washer was then rolled over onto its back as this would put the pump on top for much easier removal.

Pried off two clips attaching pump on motor using a flathead screwdriver. The r ... Read more ear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.

Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.

Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.

Replaced clips to hold motor on transmission and reinstalled screws holding clips.

IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!

Attach pump onto motor and replace clips. Double check everything is back in place.

Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.

First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.

I basically dismantled the washer and turned the washer over to access the motor,transmission and pump.I disconnected the electrical connections first.I then released the clips for the pump and the clips for the transmission.The coupler was broken in little pieces.I went to Google to search for parts and happened to reach your Web Site.I ... Read more found the part number for the coupler from the schematic and ordered it.It was then I discovered the part number for the cam dogs for the agitator so I ordered it also.While on you site I read the various troubleshooting stories and how each was repaired.I put myself through a lot of unnecessary work by dismantling the whole washer when all I had to do was turn it over and access it from the bottom.The parts arrived in three days and the install was rather simple thanks to the direction of your site.I had a heck of a time reassembling the washer but all in all $42.00 was a lot cheaper than a repairman or a new washer.We now have a working washer and no leaks.
Thanks to your site ,I have a happy wife and clean clothes.

Three of the four agitator cogs had broken. The agitator was able to spin freely both clockwise encounter clockwise which it should not be doing. I replaced the cogs as well as a couple additional parts just to be sure but the cogs were the important one. Very easy.

before ordering the parts, I pulled the cap of the agitator, removed some internal parts of the agitator - had to remove one hex head bolt, and noticed the threads on the 3 little teenie weenie plastic dogs were worn off. I bought the repair kit on line after entering the model number, parts were here in a few days, and the repair took a ... Read more bout 15 minutes. Works like new again.

The directions provided with the parts were very clear and made the job quick, easy, and painless.