25378892016 Kenmore Refrigerator - Instructions

snap and done

Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.

I unplugged the refrigerator, then opened the door and removed four screws holding the plastic electrical panel to the interior top of the main refrigerator compartment and noticed the cold control was corroded badly, apparently from moisture in the panel. I ordered a new one from partselect.com. When it arrived the next day, I then pulled off the control knob, unclipped the cold control, unplugged the three wires to the control, then removed the styrofoam insulation blocks holding the thermocouple wire and then removed the thermocouple wire to complete the removal. I then reversed the process to install the new thermostat and control. That is repositioned the thermocouple wire, put the insulation blocks back to hold the wire, then replugged the three electrical wires, clipped the control back and pushed the control knob back on and finally screwed the panel back to the top of the main compartment and plugged the refrigerator electrical cord back in to provide current to the refrigerator. It immediately started up and ran fine. Total time - about 8 minutes.

pan-crisper pan was easy because is just slide in. the drawer support rail just took a screwdriver to unscrew the screw and replace it with new rail and put the screw back in. The thing I like the best is the fast service of the parts to me.

Former tenants had broken glass bin cover and door shelf retainer. Online parts catalog was easy to use, pictures accurate, correct parts received promptly, fit is perfect. Price was couple bucks less than others. Thanks for saving us the cost of a new frig.

I had put in a new ice maker and it still had the problem, (I needed the Ice maker anyway) I installed the vale and while I was at it I put a five year filter on the water line that went from the value to the Ice maker, it took less than one hours, the ice is making like it did when it was new, I could not be more please at theis time. Thanks for your Interest. God bless.

Took whole shelf out. Unscrewed the old rail, screwed in the new rail. Female 55yrs old. I broke it myself and fixed it myself! Very easy!!!!

The repair didn't require any tools at all. Just simply slide the new glass shelf carefully into the the frame and while holding it horizontally slide the frame back into the rails. This took less than a minute to accomplish. Very satisfied with the results.

Reviewed the video on your website and followed the directions to the letter. Great video

Don't ever tell your 11 year old to clean the refridgerator. Something will almost definetly get broken like the glass shelf, but luckily I had parts select which in no time assisted me to find the exact part. I ordered the part, it came quickly and I replaced within seconds.
Thanks.

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

I removed a couple of screws from the old part, and inserted the new part. Replaced the screws and I was done. No problem. I'm an almost 60 year old woman, and fixed this myself. It was so easy.

I pulled the old gasket off and thoroughly cleaned the entire refrigerator door, including the area where the gasket would pop into. Starting at the two upper corners, I pushed the corners into the ridge in the door and used my thumbs to press the gasket in along the top of the door. I then went about halfway down the door using my thumbs to push in the gasket. Then I pushed the lower corners in, taking my thumbs up either side of the door to finish installing that section then I pushed the bottom in, checking the lower corners to make sure they were secure. Then I closed the door and made sure the seal was secure on both sides of the door.

removed the screws in the piece of the rail that was still attached and replace with new one - hardest part was the screw it was so little I started it without the magnetic screw driver - it took about 20 minutes

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.