25344733107 Kenmore Freezer - Instructions

Removed evaporator cover, unplug 2 wires to thermostat, unclipped it from the coil. Installed new themostat back the same way.

Remove access cover at bottom of case w/socket wrench (4 screws).
Attach supply line to water valve with adjustable wrench. Attach water line to ice maker on back of case (twist lock) no tools required.
Attach water line from ice maker to water valve (push connection) no tools required. Attache water valve to case at bottom w/on ... Read more e screw. (nut driver)
Reassemble access cover to bottom of case w/socket wrench (4 screws). Remove plastic cover inside freezer (w/screw driver to release from evap cover) to expose ice maker harness connection. Remove two plastic plugs (carefully w screw driver) exposing screw anchors for mounting Ice maker. Assemble two mounting screws w/nut driver. (Do not dtrive all the way in) Plug ice maker harness to plug on back of evap cover.(no tools required) Place cover over harness connection) no tools required. Guide water fill tube into fill cup on ice maker. (no tools required) Hang ice maker on mounting screws. Level Ice maker and tighten screws. (torpedo level makes it easy if you have one handy. Place Ice bucket under Ice maker on freezer shelf (lower position). Turn ice maker on and you are ready to go. Easy Job!!!!

insatlled ic maker was very eays and fast.how ever not enouh clamps for hose;s in kit in my apinion

I removed the shelves, unscrewed the cover panel of the fan motor and regulator dial, disconnected the fan motor from power, unscrewed 2 screws holding the motor to the mounting bracket and put the new motor in it's place. New motor had no thread in the mounting holes, so I put new tread in so I could use the 2 screws. Another option woul ... Read more d have been to drill all the way through the mounting holes and use longer screws or bolts. Of course I turned the power off before I started repairs. Freezer runs like new now. Technicians wanted $400 for the job, while it cost me a mere $55 for the Motor.

I unplugged the fridge and unscrewed the back cover,unscrewwd the two screws holding the water valve in place and the water line to the ice maker and the electrical connection and install the new water valve,then buttoned everything back up and plugged the fridge back in and it is working great,making ice as normal.

I first replaced the defrost timer about a week prior and it did not correct the problem. I then ordered the thermostat from partselect and within 15 minutes had the part installed. My refridgerator has been running correctly for a couple weeks.

Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process

I found a couple of videos online of a similar product fix to get a lay of the land. When I got the part, I unplugged the unit and turned off the water. It was easy to take off the back panel and remove the old water intake valve to swap it out for the new one. Once I attached everything again I could see that the valve was taking up wate ... Read more r but it didnt seem to be going all the way to the icemaker. I gave it some time and by the next day, there was fresh ice!

It was real easy but I still have problem making ice cubs
Fell problem is in the ice maker went it dose make cubs they don,t dump

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug ... Read more screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

But I have back ground mechanical skills, I did see the video one time, and everything went smooth......

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

Removed shelves ,removed panel on interior back wall with Philips screwdriver ,unplugged wire terminals slid thermostat off coil ,then reversed process to complete installation.

Shut off water supply under the sink. Removed old valve and installed new valve. Turned water back on and within a couple hours the first batch of ice made.

I removed the screws and replace the broken slide with the new slide. Put the basket drawer back on the track and it now stays in place and can easily be used once again.