25344333603 Kenmore Refrigerator - Instructions

The radiator was not being properly defrosted and the refrigerator and freezer could not keep the temperature. Two things can be causing this, the defrost module which defrost the refrigerator on a regular basis ($110) or the thermostat ($18). I tried the thermostat since it is very easy to do (remove cover plate inside the freezer, cut w ... Read more ires of old thermostat, connect new thermostat by stripping wires. Presto...however the thermostat was NOT the problem. The problem was a blown timer circuit board that controls the regular defrosting. That repair was done by a technician. The board was $110, it seats inside the refrigerator in the control panel area.

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

Unplug turn water off
Removed two screws with nut driver loosen one
Disconnected three solenoid valves
Disconnected four water lines
Plug tubing in, tighten one flare fitting
Reattach wires to solenoids
Slide under loose screw, replace two screws
Turn water on check for leaks plug in get a drink of wate ... Read more r

When the ice maker is over filling, either the valve is defective or clogged, or the ice maker is at fault signaling the valve to stay open too long. My problem was the latter. I had already replaced the valve, thinking that being only 2 years old, how could the ice maker be faulty. I was wrong. Ice maker unplugs and comes out with 2 s ... Read more crews. A quick swap with the new ice maker and all is well. Simple

The door has nylon gear teeth that wore out and needed replaced. The ice chute came off very easy with 6 screws. I used a punch and pliers to remove the hinge pin. Then the door came off and the new one put on. Very easy. The part was ordered on Sunday and arrived on Tuesday.

Unpluged the item. Turned off the water source. Removed the card board cover. Dis-connected the water hoses. Unpluged the connetors. Matched up the colores and put it back together, very easy. Everythings was color coded.

I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the a ... Read more bove procedure. Everything is color coded which made this replacement extrememly simple.

I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.

most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

First removed the drip tray with a firm tug, Then removed the 2 screws to remove the trim, had to remove the board to get get to the connector. (there is a clip that holds the wire tight) connected the new ribbon cable and secured it with the clip, screwed the board back in and pushed in the other end of the cable. and screwed the trim ... Read more back and the drip tray. surprisingly Very easy to do.

Most of the time was spent removing frozen food and removing the plastic clip holding one of the shelves in place. Removal of bottom panel took less than a minute. Thermostat easy to find, clipped wires a the unit and removed unit. Used included wire jackets, but not white shrink wrap. This did NOT fix the problem. This was the attem ... Read more pt at a 'cheap' fix. My refrigerator required the 'control box' to be replaced.

Simply slid glass into frame & it fit perfectly.

The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!

First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .

The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back pa ... Read more nel out. You will see the thermostat right away. Replace it and voila you're done.

The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the f ... Read more irst 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.