250E - Parts

This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with air compressors. The three wire cord is encased in a durable jacket and includes terminals at the end of the wires. The cord is used to relay electricity from the outlet to the switch assembly. This item is available as an individual replacement part.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling • The O-ring has ragged, tattered edges. Thes...Read moree are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is an authentic OEM part. The filter is used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The foam filter is used to prevent dirt and debris from entering and potentially damaging the pump. A hex driver, or screwdriver may be needed to install this item and it is sold individually.

This is an authentic replacement part that has been OEM sourced to be used with Porter Cable, DeVilbiss, and Black and Decker air compressors. The metal nut is commonly used to connect the outlet tube to the cylinder head assembly. This item is available as an individual replacement part, a hex wrench is needed for this repair.

This is a genuine manufacturer-sourced replacement part, it is specially designed for use with Poulan and Husqvarna chainsaws. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this hardware. Please note this durable metal nut is sold individually.

This is a genuine replacement part manufactured for use with air compressors from DeWalt. This part creates an airtight seal between the elbow and the tube. You may need a wrench to replace this part. This assembly but sleeve is sold individually and made of metal.

This safety valve is a genuine replacement part manufactured for use with air compressors. If the compressor's pressure switch malfunctions and does not turn the motor off when the amount of pressure is met, the safety valve will open to release the extra air pressure. The amount of pressure required to open the safety valve is set by the...Read more tension of the spring inside the valve. The spring can wear out, and leave the valve open at a lower pressure than what is set to turn the switch off, and will not allow pressure to build inside the tank. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality part is made of durable metal and is sold individually.

This rod kit is an original part from Craftsman for air compressors. This part attaches to the piston to the crankshaft that is in the pump. This kit includes the following: cylinder head, piston, cylinder head gasket and piston ring. You will need a wrench set and socket set to replace this part. When installing this part, it is recommen...Read moreded that that you fasten the top screw (50-60 inch- pounds). This kit is made of metal and rubber.

This metal pin is available as an individual replacement. It attaches to the left motor housing with the bar adjusting plate and helps to place tension on the bar. The pin may require a screwdriver, pliers, and a socket set to replace if it becomes broken. This is a genuine replacement part that is sourced from the original manufacturer for use with Poulan and Husqvarna chainsaws.

Used to secure the wheels on a compressor or generator, this Shoulder Bolt is roughly 3.75 inches long and is sourced directly from the original equipment manufacturer. It is made of dark grey metal, is not part of a kit or assembly, and is sold individually. This part needs to be replaced when it is damaged or worn and may cause the w...Read moreheel to fall off if it breaks. You will need a wrench or socket to complete this repair. Customers rate this repair as Easy.

Assy-cordset

Switch w/safety loc