249-623-105 (1989) MTD Log Splitter - Parts

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

This gray metal adjustable gib fits between two shafts and locks them together so they turn as one. It is 2 inches long and sold individually. Replace it if one shaft spins freely without turning the drive shaft. Turn off the machine and disconnect power before repair. Check the model number before ordering.

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This OEM Hub Cap, or Dust Cap, is a 2-inch, silver, steel part, sold individually. It requires a Rubber Mallet to install and its installation is rated as Easy by our customers. This part attaches inside the wheel on the hub, and is used to keep dirt out of the hub. It must be replaced when damaged or missing (if it is damaged it will b...Read moree out of round, and will not fit). Check your model number to ensure you are purchasing the correct part.

This hex bolt is a genuine OEM fastener used in various lawn and garden equipment and machinery. It has a hexagonal shaped head, with a diameter of 3/8 inches. The bolt shaft is 1.5 inches long with 24 threads per inch. The hexagon shape makes the bolt easier to grip and tighten using a wrench or a set of pliers. Over time, it is normal f...Read moreor the bolt to crack, corrode, or for the shaft threads to wear down. Inspect all the bolts on your equipment and replace all those that show visible signs of wear. Use a socket wrench to remove the faulty bolt(s) and thread the new one into position. Each bolt is sold individually. Secure it with a wrench or pliers and be careful not to over tighten as this could damage the bolt and equipment.

This Cotter Pin is a silver 5/32x1-1/4 metal part, sold individually and certified by the original equipment manufacturer. It connects to the axel shaft after the wheel and washer have been installed but before the hub cap. It is used to prevent the wheel from falling off, and if it breaks (due to fatigue) the wheel will fall off. Check...Read more your model number for the correct size of replacement cotter pin to know you are ordering the correct model. This is a one-time use product, which should be replaced during any other repair in which it is disturbed or dislodged.

This is an authentic replacement part, sourced from the original manufacturer for use with hydraulic log splitters. The metal nipple pipe is commonly used to link the hydraulic cylinder and the control valve. This nipple pipe is available as an individual replacement part, please see model diagram for associative parts.

This is a genuine replacement part sourced from the original manufacturer for use with log splitters. The metal hex cap screw is commonly used to secure the wedge assembly to the beam assembly. The hex cap screw is sold as an individual replacement part, please note six screws may be required.

This OEM flexible coupling connects the engine shaft to the hydraulic pump shaft in your lawn equipment to transfer power. It has a 1/2-inch inner diameter and a 3/4-inch outer diameter. Typically located in the power transmission system, a broken coupling can cause excessive vibration, unusual noises, or shaft misalignment. A broken coup...Read moreling may have physical damage like cracks or tears. Failure to replace a broken coupling can lead to further equipment damage, accelerated wear, and potential failure of connected parts. To remove the flexible coupling from your machine, you need to remove its retaining clips or fasteners with pliers or a screwdriver and detach the coupling itself afterward. You may need to apply lubricant on it if it is stubborn. This replacement part is sold individually.