2325ERS Jenn-Air Cooktop - Instructions

pulled old one out , cleaned the area & replaced with the new one.

Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen

I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away ... Read more the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!

Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.

Locate and open appropriate breaker to kill power to the range. (very important if you intend to see tomorrow).

Pull off the control knob.

Remove 2 screws that hold in control pannel.

Lift out the control pannel to the extent that the wires will let you. (2-3 inches)

Remove the nut that holds t ... Read more he switch/controller in the pannel.

Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.

Re-install the switch in the pannel.

Re-install the pannel in the stove.

Close breaker and test burner contol.

Took the old knobs off and replaced them with the new!

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..fo ... Read more r TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

OK, this was easy, and it's a good thing 'cause I'm so blonde when it comes to repairs. But I will have to say this, my Jenn-Air looks like new and it is 29 years old. Thanks Partselect for making my repairs so quick and easy.

1. Turn off power to range at circuit breaker
2. Remove grate
3 Remove control knobs
4, Remove two screws holding control panel
5. With wrench, remove locking nuts from control switches
6. Lift panel, exposing switches
7. With new switch in hand, unattach old switch one terminal at a time, attaching new swi ... Read more tch exactly as old switch, terminal by terminal.
8. Replace everything in reverse order
9.Turn on power

The part we received from your supply store, a Maytag part, was in no way a direct replacement for the original Jenn-Air switch. I had to shave material carefully off all sides of the supplied switch, including the plastic flanges that were to hold the switch in place. Consequently, there was nothing left to hold the shaved-down switch in ... Read more the opening. I had to rig two pieces of material to attach to the back of the switch to hold the switch, roughly, in place.
So, a poorly fitting replacement part that happens to function acceptably after an hour's work.
The repair: The balance of the repair was unremarkable. I simply removed the metal plate that the control knobs are mounted on, pulled it out of the rangetop, and removed the old switch. I snipped the wires, as your instructions said, nutting off the ground wire which is not used. I used a compression tool to attach the two wires to the quick-connect connectors you supplied (many home repair folks would not have a crimp tool for this job). The rest of the time was spent reshaping the switch you sent to fit into the too-small mounting hole.
I then simply returned the switch mounting plate, fastened with screws, to the range top.

Important: Down load the helpful assembly diagram for the fan motor and study it for a few minutes. It's very straight forward. Also a good idea is to remove the bottom panel which comes off easy before starting.

My only problem was removing the existing blower/fan wheel without damaging it once I had the assembly on the work b ... Read more ench. It was rusted on tight and managed to remove after a few tries using penetrating oil. The wheel is in stock and I'd suggest buying a new one along with the new motor if I had to do the job again.

Bottom line; the fan motor fit perfect but did have to re-use part of the old existing electric pig tail because the motor does not come with the factory type motor terminal connectors. By using three twist on wire connectors was back in business. The down draft vent works like new.

Wife is happy...

Wade

Turned off electricity at the circuit box. Removed four screws from panel cover that housed the switch. disconected the wires from the old switch and replaced the old switch with the new one reconected the wires put the panel cover back on. voila done.

I have bought several drip bowls over the years. They all seemed to not fit just right. These are perfect! Thanks!

I recently purchased an older home. The cooktop is aged and has not been properly maintained. With the parts I ordered from parts select I was able to bring my cooktop back to almost new! I am very pleased with the quick service parts select provided!

knobs fit perfectly