Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Downdraft Motor Bearings Shot
5 of 6 peoplefound this instruction helpful.
MICHAEL from LAKE GROVE, NY
Difficult
More than 2 hours
Nutdriver, Screw drivers, Socket set, Wrench set
I first had to purchase the replacement motor which was quoted from a high of $236 to a low at graingers of$100. 00. The counterman at graingers removed the blower fan from the motor for me with a special long handled allen key. I then degreased and cleaned the blower fan. I had to cut off the screws on the motor and replace the 3 m
... Read moreotor isolators and the urethane foam around the motor. I had to thread the 3 wires from the new motor through the bx cable from the old motor and reattach the fan to the motor. Anyone wanting more detailed informatioin may contact me at:mablume@optonline. Net
We turned off the breaker and removed the screws holding the control panel in place. They are behind in the exhaust area.
The control unit was lifted up to reveal all of the wires and the switches. Using pliers I pulled off the connectors keeping up with which wire was from which connector. The switch then dropped out and th
... Read moree new one went in and wires were reconnected.
It was not difficult. Only challenges were that it was very dense and hard to get at the wires and you had to be careful to keep up with the wire locations.
Well worth the time...I can do something other than boil water on that burner!!
Read less
Was this helpful?
Thank you for voting!
two burners had failed to work properly. Always went to full heat.
5 of 7 peoplefound this instruction helpful.
Lark from Mill Creek, WA
Really Easy
15 - 30 mins
Pliers, Screw drivers, Wrench (Adjustable)
I first removed power from the stove at the breaker panel. Next, I used the assembly diagrams provided by the parts select website to determine how to open up the stove panel. I opened the oven door to access the four screws holding the front panel holding the knobs. I removed the screws and was able to tilt up the front panel to allow a
... Read moreccess to the four burner switches. It was easy to swap out the wires on the old defective switch to the new replacement switches. I replaced both defective switches in 15 minutes and tiled the front panel back down into its normal position and put the four screws back into the panel to secure it. Then I turned on the breaker and did a check to see that the parts I replaced were working properly. They were and the total repair time was around 30 minutes without rushing at all.
Read less
Was this helpful?
Thank you for voting!
Wall vent cap & damper were broken.
5 of 7 peoplefound this instruction helpful.
Jim from Sulphur, OK
Really Easy
Less than 15 mins
Screw drivers
Attached spring to damper, placed on existing 5" duct and secured. Used screwdriver to attach vent cover to damper.
Was this helpful?
Thank you for voting!
cook top burners on old Jenn-Aire finally quit/broke
5 of 7 peoplefound this instruction helpful.
Larry from Grand Junction, CO
Really Easy
Less than 15 mins
Being able to find the right cook top on-line and order it without running around trying to find it in stores was great. Was able to replace old electric burners with new ceramic cook top. Nice to update and easy to 'plug' in the module. Thanks for being there.
Was this helpful?
Thank you for voting!
The Air Inlet Grill was corroded
5 of 7 peoplefound this instruction helpful.
Joan from Ft. Myers, FL
Really Easy
15 - 30 mins
I replaced it with a new one. I simply picked up the old one and set the new one in its place. No tools required and the part fit perfectly.
This griddle just simple slips into place above the electric elements.
The REAL story is the efficiency with which my order was filled and shipped. I was impressed! There were constant updates on my order and shipping information! Great job!
Was this helpful?
Thank you for voting!
Reusable Grease filter was old and worn out.
5 of 7 peoplefound this instruction helpful.
Gloria from Galveston, TX
Really Easy
Less than 15 mins
The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it eas
... Read morey to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.
Read less
Was this helpful?
Thank you for voting!
One burner ,of a 2 burner cartridge, was burned out. I called an appliance dealer. no help. Went on line, typed in Jenn-air cooktopand several choices came up. Clicked on yours, went thru about375 parts. Spotted what I thought was was the right one. Called in. It had three flat prongs and one ro
5 of 7 peoplefound this instruction helpful.
Wayne from Brandon, WI
Easy
Less than 15 mins
I lifted the old old cartridge on one end and slid it out. Then I shoved new cartridge in place, tried the burners. Perfect! Saved me from getting a entire new cooktop. Would recommend PartSelect to anyone looking to repair an old stove.
Was this helpful?
Thank you for voting!
Glass ceramic was damaged due to sugery spill over.
6 of 10 peoplefound this instruction helpful.
Sabry from Florence, Oregon, OR
Really Easy
Less than 15 mins
Remove and replace. It was a snap, no skill required.
Was this helpful?
Thank you for voting!
Burners not working
6 of 10 peoplefound this instruction helpful.
Wendel from Marietta, GA
Really Easy
Less than 15 mins
Plugged it in. It was that simple!
Was this helpful?
Thank you for voting!
Cooktop/grill scratched up
4 of 5 peoplefound this instruction helpful.
Terry from Brighton, MI
Really Easy
Less than 15 mins
I bought 2 covers, they are great, I can put them on and the cook top looks wonderful. I bought an older home and the Jennn-Air top was scratched up, now you cant tell at all when I put the covers on. I was thrilled to find them. I thank you
Was this helpful?
Thank you for voting!
Grandson lost the ignition key to my Toro!
15 of 38 peoplefound this instruction helpful.
Michelle from AYLETT, VA
Really Easy
Less than 15 mins
No repair, lol! Just a perfect fit for my ignition :). I bought two in case my grandson gets curious again.
My Orders
