20706 Murray Lawn Mower - Parts

This belt is an authentic Murray replacement part manufactured for use with walk-behind lawnmowers. The special belt is used to drive the wheels while using self-propulsion. Overtime belts can crack wear out and break, so it is recommended to inspect belts and pulleys as part of regular maintenance. This belt is available individually, please see model diagram for any additional parts.

This flange nut is designed for use in lawn and garden equipment. It is an OEM replacement part with a diameter of 0.375 inches and a thread pitch of 16 threads per inch. The nut has a ring-shaped extension on one end, known as a flange which helps to evenly distribute the clamping force of the nut and provide a more secure hold. Addition...Read moreally, the flange eliminates the need for separate washers and reduces the risk of abrasion on the surface being fastened. It is normal for the nut to corrode, crack, or for the threads to wear down over time. To replace the flange nut, unthread it from the fastener, and insert and secure the new one using a socket/wrench. Each sold individually.

This authentic item is supplied directly from the original equipment manufacturer for use with Murray edgers and lawn mowers. The ring goes next to the flat washer and is made of metal. When replacing this part a set of pliers might be required during the installation process. It may become bent or broken and will need to be replaced. This item is priced as an individual replacement part.

This hex center lock nut is sourced from the original manufacturer for use in lawn and garden power equipment. It is a hexagon-shaped fastener for bolts/studs that is responsible for the keeping the bolt/studs secure during use. The nut is made of metal and has a diameter of 5/16 of an inch and a thread pitch of 18 internal threads per in...Read morech. Over time the threads in the nut can wear down and the nut itself may crack or break. It is important to replace it as soon as necessary to avoid damaging your equipment. Use a socket or wrench to remove the old nut and thread the new one on. Make sure to order the correct number of nuts for your equipment as each nut is sold individually.

Keep in mind that this part is sold individually. The torsion spring is made of plastic and attaches to the rear door. A screwdriver, a set of pliers, a socket set, and a nutdriver might all be helpful during the installation of this part. It might break or bend over time and will need replacing. This genuine item is supplied by the original equipment manufacturer for use with Murray lawn mowers.

This Washer (.40.81 16g Flt) is a black, metal part, requiring a socket set to install. Installation is rated as "Easy". This washer can be used to provide a tight fit between connected components. It attaches onto the bell crank between the adjusting nut and cotter pin. Refer to your make, model and diagrams to check if this model is right for you.

Keep in mind this part is made of metal and is sold individually. The washer goes next to the extension spring. It may require a wrench during installation. Over time this part may break and will need to be replaced. This authentic item is supplied directly from the original equipment manufacturer for use with lawn tractors and lawn mowers made by Murray, Briggs & Stratton, Snapper, and Simplicity.

This replacement wheel and tire assembly is used on Murray lawn mowers. It is supplied directly from original equipment manufacturer and it is sold individually. This wheel helps to support and move mower. This assembly consists of a plastic rim and a plastic tire. This is a simple and quick repair that should only require a wrench. • ...Read more Remove the hub cap and the locknut • Replace the old wheel with the new one • Secure it with a nut and a hub cap

The retainer attaches to the idler arm support. This genuine item is supplied by the original equipment manufacturer for use with tractors and rear engine riders made by Snapper, Murray, and Simplicity. It is made out of metal and is sold individually. During the installation process, a wrench set might be needed to replace this part. Over time this part may break and will need to be replaced.

This replacement screw is supplied directly from the original equipment manufacturer for use with Murray walk-behind lawn mowers. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this part. This is a high-quality co...Read moremponent which is made of durable metal and it is sold individually, the washer is included.