2049 - Parts

This item is an authentic replacement part that has been sourced from the original manufacturer to be used with lawnmower engines from Briggs & Stratton and Toro. The metal float bowl fits onto the bottom of the carburetor and is used to house the float and store and drain the fuel that actuates the needle valve. This item is available as an individual replacement part.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secures the drive pinion gear to the drive shaft, and if broken due to wear/fatigue/damage, it will need to be replaced.

This is a genuine OEM sourced replacement part. It is designed for use with lawn and garden engines. It is an important part of the starter assembly that is used to crank start the unit. Please note shroud/housing, starter pulley, starter spring, grip, the pull rope and the hardware are all sold separately. This pawl plate is made out of ...Read moreplastic and it is sold individually. To complete this repair you would need a wrench.

This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to ...Read moreyour make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.

This is an Authentic OEM replacement part used on Lawn and Garden Engines. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won\'t start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull th...Read moree starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This Assembly includes a Metal Body Carburetor, Rubber O-Ring and a Gasket. When replacing Carburetor it is advised that you also replace Carburetor Gaskets to ensure proper Air Tight Seal for optimum performance. You will need a Screwdriver to perform this repair.

This is a genuine part which is supplied directly from the original equipment manufacturer and is used with Craftsman lawn mowers. The cylinder head gasket attaches between the engine block and the cylinder head. This part is made head resistant material and is sold individually. For this repair, you will need a screwdriver to remove any ...Read morecovers or shrouds to aid you. Before starting this repair, let the engine cool and disconnect the spark plug wire.

This fuel tank is for lawn and garden equipment engines. Fuel tank holds the gas that's needed by the engine. Work in a well-ventilated area when installing this part. Drain the existing fuel from the tank and disconnect the spark plug wire before beginning the repair.

This genuine replacement magneto is designed for Briggs & Stratton engines used in Toro lawn mowers. It plays a vital role in the ignition system by generating the electrical current needed to fire the spark plug. Made from high-quality materials, this part is sold individually. Note: The spark plug boot is sold separately. To replace...Read more the magneto, begin by removing the housing or covers from your mower. Next, remove the spark plug and bind the cylinder to prevent it from turning. Disconnect the ignition wires and remove the old ignition coil. Install the new magneto, carefully setting the correct air gap between the coil and the flywheel. Once installed, reassemble the unit and test for proper operation. A screwdriver set is recommended for this repair.

This is a genuine OEM supplied replacement part designed for use with Briggs and Stratton engines. This float controls fuel flow into the carburetor bowl by adjusting the needle valve. Includes a plastic float and a metal pin. To complete this repair you would need a wrench and pliers.

Genuine OEM sourced part used on variety of Toro Lawn and Garden Equipment. This part is sold individually and the Nut is not included. The square area under the head is designed to fit into a square hole in the workpiece. It is this square hole that restrains the bolt and keeps it from turning when the nut is tightened.

The O-Ring is a black rubber part, used to provide a seal between two pieces. It can be used in various locations on a variety of equipment. Installation is rate as "Easy" and will require a screw driver, pliers, socket set, and wrench set. If broken, damaged, or worn due to fatigue, you will have a leak and the part must be replaced. Refer to your make, model and diagrams to see if this is the right part for you.