2040-2 Makita Planer Jointer - Parts

This is an Authentic OEM Approved replacement part designed for use with Makita Planers/Jointers. This part is made out of Metal and it is Sold Separately. This part helps to secure the Roller and allows it to spin smoothly. To replace this part you would need Retaining Ring Pliers, Screwdriver and a Set of Wrenches.

This is an OEM part sourced directly from the manufacturer. The hex bolt is designed for use in Makita miter saws and planer-jointers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different bolts used in the machine. Refer to the parts diagram to b...Read moree sure of ordering the correct part. You will require a wrench when replacing this part. This item is sold individually.

This part is available individually. The spring washer fits between the wing nut and the flat washer. This washer is small and will need to be replaced if it gets lost or if it breaks. It is made out of metal and no tools should be necessary when replacing this item. This is an OEM Makita part directly sourced from the manufacturer for use with saws, cutters, planers, drills, and trimmers.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 16 Gauge • 8 Feet Long

This is a genuine item that is supplied directly from the original equipment manufacturer for use with Makita power tools. It is an identical replacement for a missing or damaged rubber pin that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and applicat...Read moreion of this hardware. Keep in mind this high-quality item is made of durable rubber material and is sold individually.

This star drag spring is a genuine part which is supplied by the original manufacturer for use with Makita planers. The spring applies tension on the connected components of the tensioner mechanism. Over time it can wear out, get damaged or lost eventually requiring a replacement. Refer to the diagrams for your model to ensure the correct...Read more repair procedure. This tension spring is made of high-quality metal and is sold as an individual item.

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fi...Read morex an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.

This cord guard / strain reliever is a genuine Makita replacement part. It covers the final portion of cord before entering the tool, providing extra rigidness and preventing cord damage. Over time these cord guards break down and require replacement. The guard is constructed of heavy duty rubber compound for toughness. This cord guar...Read mored is compatible with the tools listed below. It is not guaranteed to fit any other power tool models.

This genuine OEM woodruff key is a small, semicircular metal piece used in various power tools to connect rotating parts, such as shafts or gears, to other components like wheels or pulleys. It prevents slippage between these parts, ensuring smooth synchronization and power transmission. With a width of 3/32 inches and a length of 5/8 inc...Read morehes, consider replacing a woodruff key if you notice misalignment or excessive movement between the connected parts. Be sure to inspect the key for signs of wear, damage, or bending. Removing the key depends on the make and model of your tool. If the key is visible, gently tap it from one side using a small hammer and a punch or drift pin. This will dislodge it from its slot. If the key is stuck or difficult to access, you may need to partially disassemble the tool to gain better access to the key. Once the key is loose, carefully pull it out using pliers. Clean the keyway and slot before installing the new key. Before making your purchase, remember that this component is sold individually.

This fifteen (15) pin sprocket is an authentic part made by original manufacturer. It is compatible with some Makita planers/planer-jointers. A sprocket engages and drives a chain and/or gear. This item is sold individually.