20331 Toro Lawn Mower - Overview

This is a replacement air filter/AC cartridge for your small engine. The air filter prevents dirt and debris from entering the engine. Over time, the air filter can become clogged or damaged, and this can lead to reduced performance. This air filter is approximately 4 inches wide and approximately 5 inches long. To replace the air filter,...Read more locate the air filter cover on the side of the engine, unscrew it, and remove the old filter. Be sure to clear out any dirt, clippings, or other debris that has found its way into the air filter assembly before you insert the new filter. Reattach the air filter cover, and secure it with the screws. This product is sold individually.

This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.

The Air Cleaner Gasket is used to provide a seal between the air cleaner base, and carburetor. It's a gray, composite material part, which is rated as "Easy" to install and will require a screw driver, pliers, socket set, and nut driver. It attaches between the base of the air cleaner assembly and carburetor. If broken, damaged or worn do...Read morewn it will allow dirt to enter the carburetor, causing performance issues. If this happens, replace it. Refer to your make, model and diagrams to check if this is the right part.

This genuine OEM engine gasket set is sourced directly from the manufacturer and includes the gaskets needed to seal the components in a gas-powered engine. This set ensures proper fit and performance to maintain the life of your lawn equipment engine. When installing replacement gaskets, make sure to wear work gloves to protect your hands.

The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. Installation is rated as "Easy" by customers and will require a socket set. This part is individually sold, gray, and constructed of metal. R...Read moreefer to your make, model and diagrams to check if this is the right part for you.

This is a genuine OEM replacement blade for use on Lawn Mowers. If the blade is too dull it will tear the grass instead of an even cut. A bent or damaged blade can cause serious damage or injuries. You can use this blade with the Recycler Cutting System to chop grass clippings into fine mulch particles and return them to the ground.

This is an authentic OEM replacement part used on lawn and garden engines. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. This Carburetor is a auto-choke system. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspo...Read moreon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This assembly includes a metal body carburetor, rubber o-ring and a gasket. When replacing carburetor it is advised that you also replace carburetor gaskets to ensure proper air tight seal for optimum performance. You will need a screwdriver to perform this repair.

This is a manufacturer approved replacement part designed for use with a variety of lawn and garden engines. The air vane spring maintains the proper tension on the air vane choking system. If it is broken, it can cause the engine to not start. To replace it you will need pliers.

This item is an authentic replacement part that has been sourced from the original manufacturer to be used with lawnmower engines from Briggs & Stratton and Toro. The metal float bowl fits onto the bottom of the carburetor and is used to house the float and store and drain the fuel that actuates the needle valve. This item is available as an individual replacement part.

This cable-traction is sourced directly from the original equipment manufacturer. It is specially designed for use with Toro lawn mowers. The traction cable engages drive wheels on the equipment. Over time it may wear out or get damaged eventually requiring a replacement. It is connected to the bail and then attached to the traction brack...Read moreet near the transmission. Refer to the owners manual and the appropriate diagrams of your model for the exact location and the correct installation. One durable rubber insulated cable is included. You may need pliers and a wrench set to disconnect the old part and attach the new one.

This is a genuine OEM sourced replacement part designed for use on Toro lawn mowers. It is mounted to the side of the mower for the cut grass to be expelled out of it. This part is made out of plastic and it is sold individually. Please note the hinge bracket assembly and spring used to secure this deflector are sold separately.

The Toro Rear Baffle is a genuine OEM part designed specifically for your lawn mower. This crucial component attaches under the mower deck, effectively directing grass clippings out the discharge chute. It is important to wear work gloves during installation to protect your hands. Ensure maximum performance and optimum functionality of yo...Read moreur lawn mower with this Toro Rear Baffle. Made with the trusted Toro brand quality, this part guarantees durability and perfect fit for your mowing needs. Enjoy a cleaner, smoother mowing experience with the Toro Rear Baffle.