20331 (310000001-310006219 - 2010) Toro Lawn Mower - Overview
Sections of the 20331
[Viewing 6 of 6](2010)_WW_1.gif "Engine and Blade Assembly Diagram and Parts List for 310000001-310006219 - 2010 Toro Lawn Mower")
(2010)_WW_2.gif "Handle Assembly Diagram and Parts List for 310000001-310006219 - 2010 Toro Lawn Mower")
(2010)_WW_3.gif "Housing Assembly Diagram and Parts List for 310000001-310006219 - 2010 Toro Lawn Mower")
(2010)_WW_4.gif "Rear Bag Assembly Diagram and Parts List for 310000001-310006219 - 2010 Toro Lawn Mower")
(2010)_WW_5.gif "Rear Wheel and Height-of-Cut Assembly Diagram and Parts List for 310000001-310006219 - 2010 Toro Lawn Mower")
(2010)_WW_6.gif "Transmission, Front Wheel and Height-of-Cut Assembly Diagram and Parts List for 310000001-310006219 - 2010 Toro Lawn Mower")
Keep searches simple, eg. "belt" or "pump".
Washer-Stepped
PartSelect #: PS9048394
Manufacturer #: 614426
The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. I...
$3.99
In Stock
Blade-22 Inch
PartSelect #: PS11804777
Manufacturer #: 131-4547-03
This is a genuine OEM replacement blade for use on Lawn Mowers. If the blade is too dull it will tear the grass instead of an even cut. A bent or damaged blade can cause serious damage or injuries. Yo...
$24.90
In Stock
Bolt-Shoulder
PartSelect #: PS9046634
Manufacturer #: 614650
The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket...
$4.99
On Order
Questions And Answers for 20331
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The hub that the mower blade mounts to was broken
The hub that the mower blade mounts to was brokenPut the new Harbonne played and played securing flange bolted it up
Parts Used:
-
randy from HIGHLAND, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
7 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
trailing shield had broken off the mower, rendering bag useless.
-
Judy from PRINCETON, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench (Adjustable)
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Read less
Parts Used:
-
Ray from YARDLEY, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set, Wrench set
3 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!