Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake Element Broke in Two
5 of 5 peoplefound this instruction helpful.
Fred from New Windsor, NY
Really Easy
Less than 15 mins
Screw drivers
My spouse calls me Mr. Breakit--and she's right. I was delighted to read others' accounts that this was easy, but I wasn't sure. When the part arrived, we had 1 hour before company arrived. I took two screws out of the plate (tight--I had to apply a lot of torque), slid the old piece out, attached the new piece, put the screws back in. Vo
... Read moreila! (Oh, yeh, do remember to turn the juice off.) We were "cooking" in about ten minutes. So easy a caveman could do it. And I did.
Read less
Was this helpful?
Thank you for voting!
The oven wouldn't heat because the bake element had burned a hole through the wall of the element tube.
5 of 5 peoplefound this instruction helpful.
Richard from Columbus, NC
Really Easy
Less than 15 mins
Screw drivers
"First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and removed the two wires." from the burned out element. I plugged in the new element, reinstalled the new element and, 10 minutes start to finish, the oven heats again. So easy even I can do it. !!!
Was this helpful?
Thank you for voting!
heating coils (burners) were not working
6 of 8 peoplefound this instruction helpful.
Carol from Holbrook, NY
Really Easy
Less than 15 mins
when the new cartridges came in all I did was unplug the old and plug in the new and I had a new stove
Was this helpful?
Thank you for voting!
Blower Motor Stopped running
7 of 11 peoplefound this instruction helpful.
Edwin from Bellevue, WA
A Bit Difficult
More than 2 hours
Pliers, Screw drivers, Socket set
Removed the blower assy. Removed the motor. installed the new motor. Reassembled the blower assy. The problem I had was getting the proper clearance for the squirrel cage blower fan to rotate without rubbing on something. I had to make shims for the mounting flanges of the housing to get it to work. Took a lot of head scratching.
Was this helpful?
Thank you for voting!
high blower vibration
10 of 21 peoplefound this instruction helpful.
Lawrence from Chandler, TX
Really Easy
1- 2 hours
Nutdriver, Pliers, Screw drivers, Socket set
blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.
Old stove burners were rusted out and hard to clean
6 of 9 peoplefound this instruction helpful.
Pamela from Kerrville, TX
Really Easy
15 - 30 mins
Unplugged old units and plugged in new units. They fit perfectly and it was all so easy. I have been very happy with PartSelect services.
Was this helpful?
Thank you for voting!
Cartridge was in need of replacement unit
5 of 6 peoplefound this instruction helpful.
Marion from Center Point, IA
Really Easy
Less than 15 mins
Unplugged unit,cleaned stove and replaced new cartridge.
Was this helpful?
Thank you for voting!
I had just installed new burner moduels on my stove top but was unable to find a cover for my grill and decided to go on line to look for one. I was thrilled when I located just what I was looking for. I also had a problem with large pots and pans causing a dark grease like stain on the stove top ar
6 of 9 peoplefound this instruction helpful.
Carol from Frisco City, AL
Really Easy
Less than 15 mins
All I had to do was insert the new burner and place the grill cover over the existing grill top. Works like a charm.
First of all the part arrived a day and a half after ordering which we thought was remarkable. We unplugged the griddle unit and plugged in the cartridge with two burners. It is beautiful.
Thanks.
Was this helpful?
Thank you for voting!
part was just looking old and worn
5 of 6 peoplefound this instruction helpful.
Geri from El Dorado, CA
Really Easy
Less than 15 mins
Really simple just had to remove the old part by simply pulling it out of the socket and then insert the new cartridge. It looks great it was shipped in a matter of days I was surprised to get it so soon.
Was this helpful?
Thank you for voting!
Loose terminal caused block to overheat and break
6 of 10 peoplefound this instruction helpful.
Dana from Black Mountain, NC
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Was this helpful?
Thank you for voting!
burner would only get super hot. could not control temp.
5 of 7 peoplefound this instruction helpful.
Thomas from Exeter, NH
Really Easy
Less than 15 mins
Screw drivers
removed 4 screws holding burner controls. removed wires off old and placed on new burner control. very pleased with quick shippig of part. two days and range was as good as new. excellent company to buy from
Was this helpful?
Thank you for voting!
Burners not working
6 of 10 peoplefound this instruction helpful.
Wendel from Marietta, GA
Really Easy
Less than 15 mins
Plugged it in. It was that simple!
Was this helpful?
Thank you for voting!
Surface of griddle was worn out
4 of 4 peoplefound this instruction helpful.
Judith from Sour Lake, TX
Really Easy
Less than 15 mins
This griddle just simple slips into place above the electric elements.
The REAL story is the efficiency with which my order was filled and shipped. I was impressed! There were constant updates on my order and shipping information! Great job!
Was this helpful?
Thank you for voting!
Wall vent cap & damper were broken.
5 of 7 peoplefound this instruction helpful.
Jim from Sulphur, OK
Really Easy
Less than 15 mins
Screw drivers
Attached spring to damper, placed on existing 5" duct and secured. Used screwdriver to attach vent cover to damper.
My Orders
