20131 - Parts

This is a genuine OEM sourced replacement part. It is designed for use with lawn and garden engines. It is an important part of the starter assembly that is used to crank start the unit. Please note shroud/housing, starter pulley, starter spring, grip, the pull rope and the hardware are all sold separately. This pawl plate is made out of ...Read moreplastic and it is sold individually. To complete this repair you would need a wrench.

This genuine fuel tank assembly is sourced directly from the original equipment manufacturer and is specifically designed for use with Briggs & Stratton engines on lawn and garden equipment. It serves as the primary reservoir for storing fuel required by the engine. Constructed from durable plastic, this assembly includes both the fuel...Read more tank and cap. Note: Mounting hardware and fuel lines are sold separately. This tank features four mounting holes for secure installation. For proper fit and installation, refer to your equipment’s model diagram.

Discover the Briggs and Stratton Armature-Magneto, a vital component for optimal operation of your lawn and garden equipment engines. This premium-quality ignition coil significantly contributes to spark plug voltage generation. It's recommended that you suit up with work gloves before you start the installation process to ensure your han...Read moreds are completely protected. For your convenience, we provide a comprehensive installation guide, which consists of helpful DIY instructions to assist you in properly setting up the part. Trust only Briggs and Stratton for dependable equipment parts that offer long-standing durability and improved performance.

This is a genuine replacement pre-cleaner filter used with Briggs and Stratton engines. It is supplied directly from original equipment manufacturer. Its purpose is to filter out dust and debris from contaminating the engine. This filter is made out of paper and metal. This item is sold individually. Replacing this filter is a simple that that would only require a wrench.

This replacement push rod is specially designed for use on Briggs and Stratton engines. It is an authentic part supplied directly from original equipment manufacturer. The push rod is connected to the camshaft to push the exhaust valve open during the exhaust stroke. A bent rod can not only affect your engine's performance, it can serious...Read morely damage other parts if the problem is not taken care of immediately. Please note, this assembly includes the (1) push rod and (1) tappet valve.

A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other ...Read moresmall engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.

This is a genuine manufacturer sourced replacement part designed for lawn and garden equipment engines. This gasket provides an air-tight seal for the float bowl. Over time this gasket will shrink, become brittle and crack allowing for air leaks. At that time it should be replaced. It is made out of rubber material and it is sold individually. Replacing this item you would need a screwdriver.

This spark plug is an authentic OEM replacement part, it is not an aftermarket equivalent. It is specially made for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. A spark plug helps to deliver electric current from an ignition system to the combustion chamber. Please note, this item is sold indi...Read morevidually. You should always gap the spark plug in accordance with the owners manual of the outdoor product you have. Replacing a spark plug you will need a apark plug wrench or a socket wrench to get the job done.

This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to transfer vacuum from the engine. Unfortunately, over time the material may wear out and begin to crack eventually ...Read morerequiring a replacement. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. Note, this item includes one durable rubber hose and two metal clamps to secure it.

This authentic manufacturer sourced replacement part is designed for use with lawn and garden engines. The starter motor provides an initial motion, engage the flywheel to start the engine. This starter motor features a 14 tooth metal gear. To complete this repair you would need a wrench.

This is a genuine OEM part. The Briggs & Stratton valve seal is used on many lawn tractor machines. The metal part stops oil from moving into the cylinder from the valve stem. This item is often fastened to the intake valve and the valve keeper. A screwdriver, socket set and wrench set are required for the installation. The metal valve seal is sold individually.

This is a genuine manufacturer-sourced part which is designed for use on lawn and garden equipment. It is an identical replacement for a missing or a damaged clamp that is used to secure the hose. Keep in mind this high-quality product is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams for your model for the correct location and application of this hardware.