2003 - Parts

This durable nylon starter rope is an authentic OEM supplied replacement part that is specially produced for use with Briggs and Stratton engines that are commonly installed on Toro lawn and garden equipment. When the rope is pulled to start the engine, it is returned back into the starter pulley by means of the starter spring. One starte...Read morer rope is included per order, please note the handle grip and other parts are all sold separately.

It is an authentic Toro hardware. The washer-clutch is supplied from the original equipment manufacturer for use on lawn mowers. It helps to engage the pinion gear which is an important component that drives the wheel assembly. If the motor runs but the drive wheel is not spinning, a broken or worn washer-clutch may be the reason. To ensu...Read morere the exact location and the correct application of this item, refer to the appropriate diagrams of your model. Note, one durable plastic washer-clutch is included. You will need a wrench set to remove and resecure the wheel when replacing this hardware.

The Handle (or Knob Handle) is a black, plastic part which is rated as "Easy" to install by customers. It attaches onto the handle, so you can quickly release to fold down the handle bar. If the part is visibly broken (due to wear/fatigue), it should be replaced. Refer to your make, model and diagram to check if this is the right part for you.

It is a genuine manufacturer-sourced item that is specially made for Toro and Lawn Boy lawn mowers. The drive control cable is the cable that stops the blade when the control handle is released. This part provides an identical replacement for a missing or a faulty bail-brake that was installed on a new unit. Please make sure to refer to t...Read morehe appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality bail-brake is made of durable metal and is sold individually.

This is a genuine replacement part that has been sourced from the original manufacturer to be used with small engines from Briggs & Stratton and Toro. The pan head screw is commonly used to secure the blower housing assembly. This item is sold as an individual replacement part. A screwdriver is needed to complete this repair.

This authentic replacement part is supplied by original equipment manufacturer for use on Toro walk behind lawn mowers. This cable consists of a metal wire cable with z-type bent ends and rubberized cover/body. The control cable stops the blade when the control handle is released on walk-behind mowers. If the cable is broken it will cause...Read more the brake to not release even when the lever is pressed. You may need pliers to complete this repair. • First you want to see where the old cable is attached to the motor assembly • Just remove the cable end there and install the new one • Now you can run the new cable up to the control handle • Then just as the old cable, put the z-shaped end through the hole in the control handle • Once both ends are attached, just push the upper mount assembly of the old cable out of the hole in the upper handle • Tie the cable in place just as the old one was, but leave enough clearance and free play to avoid over-bending and breaking the new cable

This genuine replacement part is supplied from original equipment manufacturer. It is a commonly used item on Toro lawn mowers. The purpose of this shoulder bolt is to secure a wheel to the axle. This bolt has a hex head which requires a wrench to secure. Includes one (1) bolt per order.

This item is a genuine Toro replacement part that is OEM sourced to ensure quality. The plastic knob is intended to be used with walk-behind lawnmowers. This item attaches to the height adjustment lever and is used as a grip when changing the cutting height of the deck. The lever knob is priced individually and four may be needed.

This authentic item is supplied directly from the original equipment manufacturer for use with engines, outboard motors, portable generators, snowthrowers, and lawn mowers made by Briggs & Stratton and Toro. The o-ring seal attaches to the dipstick. When replacing this part a socket set might be required during the installation process. I...Read moret is made out of rubber and will need to be replaced if it breaks. This part is available as an individual replacement.

This item is an authentic Toro replacement part that has been sourced from the original manufacturer to be used with lawnmowers. The geared wheel attaches to the trans axle and couples with the pinion gear to drive the mower. This item is available as an individual replacement part.

This replacement intake gasket is an authentic OEM sourced part that is specially produced for use with Tecumseh engines commonly installed on Toro lawn and garden equipment. Its purpose is to create an air tight seal for the carburetor air intake pipe. Over time gaskets will deteriorate and may crack eventually requiring a replacement. It is made from high quality composite material and it is sold individually.