20029 - Parts

Genuine Manufacturer Sourced replacement part used on a variety of Briggs and Stratton Engines. This filter adds a second layer of protection against airborne-dirt particle ingestion. This is a Foam Pre-Cleaner which is Sold Individually. Please note a Paper Filter and a Cover are both Sold Separately.

This authentic OEM starter assembly is designed for use with lawn and garden engines and is sourced directly from the original manufacturer to ensure quality and compatibility. The assembly includes a durable plastic shroud/housing, starter pulley, recoil spring, pull rope with grip, and the necessary hardware for installation. It functio...Read morens as the primary mechanism for manually cranking and starting the engine. To complete the replacement, you’ll need a wrench. Simply remove the four screws and nuts securing the old starter assembly, then install the new one using the included hardware. This item is sold as a complete individual assembly.

This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This cable barrel holder is a genuine OEM part that is designed for use with tillers and snow throwers. Sold as an individual part, this holder measures approximately 1-inch in length and is used to secure the clutch control handle and cable together. This holder is made of durable plastic and can replace the old holder by simply removing...Read more it, inserting the cable into the new holder, and tightening it until it is locked in place.?

This item is an authentic replacement part that has been sourced from the original manufacturer to be used with lawnmower engines from Briggs & Stratton and Toro. The metal float bowl fits onto the bottom of the carburetor and is used to house the float and store and drain the fuel that actuates the needle valve. This item is available as an individual replacement part.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secures the drive pinion gear to the drive shaft, and if broken due to wear/fatigue/damage, it will need to be replaced.

This is a genuine OEM sourced replacement part. It is designed for use with lawn and garden engines. It is an important part of the starter assembly that is used to crank start the unit. Please note shroud/housing, starter pulley, starter spring, grip, the pull rope and the hardware are all sold separately. This pawl plate is made out of ...Read moreplastic and it is sold individually. To complete this repair you would need a wrench.

The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket and is rated as "Easy" by customers. It is mostly used to keep the wheel in place. It fits onto the unit frame and if broken or removed, th...Read moree wheel will fall off. Refer to your make, model and diagram to ensure this is the correct part.

This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to ...Read moreyour make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.

This item is available as an individual replacement part but also includes the screws. The muffler deflector attaches to the lo-tone muffler and is made of metal. A nutdriver might be required during the replacement of this item. It may become broken and will need to be replaced. This is an authentic Briggs & Stratton and Toro replacement...Read more part that is sourced from the original manufacturer for use with engines, snowthrowers, tillers, lawn mowers, and lawn tractors.