20027 Toro Lawn Mower - Parts

The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket and is rated as "Easy" by customers. It is mostly used to keep the wheel in place. It fits onto the unit frame and if broken or removed, th...Read moree wheel will fall off. Refer to your make, model and diagram to ensure this is the correct part.

This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to ...Read moreyour make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.

This replacement part is designed for use with Briggs and Stratton engines installed on lawn and garden equipment. It is used to filter out dust and debris from contaminating engine and carburetor. This cartridge will get dirty over time requiring replacement. This is a pleated paper filter with a plastic base/frame. Includes one (1) filt...Read moreer cartridge per order. Please note foam filter is sold separately. Replacing air filter is easy and does not require any tools. • First remove the knob • Remove cover and take out old air filter • Clean out the filter base/housing • Place new air filter in the case • Reassemble and test the engine

This is a high quality replacement hardware that is specially manufactured for use on Toro lawn and garden equipment. Two of these screws are generally used to secure the belt guide to the mower deck. Please note this durable metal hex head taptite screw is included per order.

This fuel tank is for lawn and garden equipment engines. Fuel tank holds the gas that's needed by the engine. Work in a well-ventilated area when installing this part. Drain the existing fuel from the tank and disconnect the spark plug wire before beginning the repair.

This genuine replacement magneto is designed for Briggs & Stratton engines used in Toro lawn mowers. It plays a vital role in the ignition system by generating the electrical current needed to fire the spark plug. Made from high-quality materials, this part is sold individually. Note: The spark plug boot is sold separately. To replace...Read more the magneto, begin by removing the housing or covers from your mower. Next, remove the spark plug and bind the cylinder to prevent it from turning. Disconnect the ignition wires and remove the old ignition coil. Install the new magneto, carefully setting the correct air gap between the coil and the flywheel. Once installed, reassemble the unit and test for proper operation. A screwdriver set is recommended for this repair.

This is a genuine OEM supplied replacement part designed for use with Briggs and Stratton engines. This float controls fuel flow into the carburetor bowl by adjusting the needle valve. Includes a plastic float and a metal pin. To complete this repair you would need a wrench and pliers.

Genuine OEM sourced part used on variety of Toro Lawn and Garden Equipment. This part is sold individually and the Nut is not included. The square area under the head is designed to fit into a square hole in the workpiece. It is this square hole that restrains the bolt and keeps it from turning when the nut is tightened.

This is an OEM sourced replacement part used on Briggs and Stratton and Toro equipment. Its purpose is to provide an extra layer of protection from dust and other contaminants. One foam air cleaner filter is included per order. Please note, the main pleated paper filter is sold separately. Depending on your equipment you may need a scre...Read morewdriver to replace this filter. • Remove the cover • Take out the old filter • Secure the new filter in place • Reattach the filter cover

This is an authentic OEM sourced replacement part that is intended to be used with lawnmower engines and outboard motors from Briggs & Stratton and Toro. The metal screw is used to secure the rocker cover to the cylinder head assembly. This item is available as an individual replacement part.

This screw is an OEM part sourced directly from the manufacturer and is used in Toro snowthrowers. It requires a wrench and connects the ring-chute to the chute-discharge. The screw is made of metal and is sold as an individual part. Screws will need to be replaced when they become stripped.

This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to transfer vacuum from the engine. Unfortunately, over time the material may wear out and begin to crack eventually ...Read morerequiring a replacement. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. Note, this item includes one durable rubber hose and two metal clamps to secure it.