20013 - Parts

Genuine OEM replacement part used on Walk Behind Mowers and Snowblowers. This is a Plastic Knob with a Metal Bushing inside. Does not ship with screw or washer these parts are sold separately. Replacing this part is very easy and it does not require any additional tools.

This OEM Carburetor Bowl Gasket attaches between the carburetor bowl and carburetor in order to seal the parts together. This model is rubber, black, and comes individually sold. Installation is rated as "Easy" by customers, and will require pliers and a socket set. If the part becomes broken due to wear/damage then there may be a fuel le...Read moreak, and the part will need to be replaced. Refer to your make, model and diagrams to ensure you've chosen the correct part.

This is a Genuine OEM Toro Pinion Gear, with 15 teeth, which drives the gear on the wheel. This part is sold individually. There are two of these gears used on the Mowers for the left and right sides. If the gear is showing signs of damage or wear it needs to be replaced.

This screw is an OEM part sourced directly from the manufacturer and is used in Toro snowthrowers. It requires a wrench and connects the ring-chute to the chute-discharge. The screw is made of metal and is sold as an individual part. Screws will need to be replaced when they become stripped.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

Used on small engines in walk-behind lawn mowers, this paper air filter element helps keep dirt and debris out of the engine to support smooth operation and consistent performance. Designed as a routine maintenance item, it promotes proper airflow while protecting internal components from premature wear. Easy to install and replace, this ...Read morefilter is ideal for seasonal service or more frequent changes when operating in dusty or demanding conditions.

This is a genuine OEM sourced replacement part designed for use with lawn mowers. This thrust washer helps to secure the pinion gear. It helps to distribute the pressure evenly and provides a tight seal for the connecting pieces. It is made out of metal and it is sold individually. Replacing this washer you would need a wrench and pliers.

This is a Genuine Manufacturer Approved replacement part used on some Push Lawn Mowers. This part is sold individually. The Traction Cable engages drive wheels on the lawn mowers. It is connected to the Traction Bail and then attached to the traction bracket near the transmission.

This OEM-sourced washer in your walk-behind lawnmower provides space and protects the rear wheel from rubbing against the pivot arm assembly, ensuring smooth wheel rotation. A damaged washer may appear worn or cracked, causing the rear wheel to feel misaligned or wobble excessively. If not replaced, it can lead to increased wear and expen...Read moresive repairs. To remove the existing washer, prop up the wheel with a two by four, use a wrench to remove the bolt securing the wheel, slide out the wheel, and then remove the bolt on the rear adjuster to take off the washer. Please note that this washer is sold individually, so make sure to check the quantity needed for your machine before making your purchase.

This is an authentic manufacturer sourced replacement part designed for use with Toro walk-behind lawn mowers. This part helps to secure the mower wheel, allowing it to rotate freely. It is made out of metal and it is sold individually. To replace this part you would need a wrench and pliers.

The Blade Support is a 6-x-3-inch Black, metal part used to support the blade. It's rated as "Easy" to install by customers. It must be torqued to manufacturer specifications which will require a socket set and wrench set. It attaches to the blade assembly. If there are rattling sounds or other srange sounds coming from the blade area tha...Read moret is a sign the part has been broken or damaged due to wear or fatigue and should be replaced. Refer to your make model, and diagrams to ensure you choose the right part.

The Fuel Line Clamp is a metal, individually sold part which clamps onto the fuel line, securing it to a port and preventing leaks. Installation is rated as "Easy" by customers and will require pliers and a screwdriver. If broken due to wear/fatigue/damage, there may be a fuel leak and the part should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.