All Installation Instructions for General Electric Ice Maker 1993LPO

fridge was warm

46 of 79 people found this instruction helpful.

ELLIS from LEANDER, TX
Really Easy
Less than 15 mins
Nutdriver

first remove the one screw holding the cover over the defrost timer, grasp the timer and unplug from the male plug end. insert the new timer. replace the cover and the one screw. plug in the fridge enjoy.
my old fridge was 30 years old and i had to replace the timer many times.

Was this helpful?

Door shelf retainer was damaged

3 of 4 people found this instruction helpful.

Arnold from Lighthouse Point, FL
Really Easy
Less than 15 mins

I removed the original retainer and installed the new one.

Was this helpful?

we had a broken clip and bent door guards

4 of 7 people found this instruction helpful.

Elizabeth from Greenacres, FL
Really Easy
Less than 15 mins

First we removed he old parts and just popped out the new ones out of the plasric bags and put them in place it was awesome. and so much cheaper than going through a local parts store. I would definitely use again. Thank you so much.

Other Parts Used:

Freezer Shelf Bar - White

Door Shelf Retainer Bar

Retainer Bar End Cap - Left or Right Side

Was this helpful?

The part that holds the items in the door was bent.

2 of 2 people found this instruction helpful.

victoria from forest park, IL
Really Easy
Less than 15 mins
Screw drivers

I removed the brackets with the metal strip attached, from the door. I took a screwdriver and pressed down on the parts holding the strip to the brackets . I attached the new strip to the brackets and then attached the whole thing to the door.
Really easy to do.

Was this helpful?

Water Leaking out of bottom of refrig first then out of vegetative bins underneath

2 of 2 people found this instruction helpful.

robert from Vicksburg, MS
A Bit Difficult
More than 2 hours
Nutdriver, Pliers, Screw drivers, Wrench set

Replaced defrost thermostat and defrost controller and also noticed that run capacitator for compressor almost oxidized in two and ordered and replaced and cleaned out drain tube and invertor (which was blocked by frozen peas and other food)or water to drain during defrost cycle and put everything back together and seems to work fine now. ... Read more

Read less

Was this helpful?

door shelf bar was bent and no longer holding in items

2 of 3 people found this instruction helpful.

jamie from san clemente, CA
Really Easy
Less than 15 mins

we ordered new bar, cut to fit with instructions, and voila! easy!

Was this helpful?

The old retainer bar was dented outward and did not keep condiments in place

1 person found this instruction helpful.

Heather from YAKIMA, WA
Easy
Less than 15 mins
Screw drivers

I detached the end caps from the fridge and the old bar. They are plastic pieces which do not have any screws, just a little plastic lever that is easily removable with a screwdriver. I then fitted the end caps to the new retainer bar and attached to the fridge.

Was this helpful?

Door retainer for condiments broke

1 person found this instruction helpful.

David from WALLINGFORD, CT
Really Easy
Less than 15 mins

Ordered new end clips and installed .Snap together parts

Was this helpful?

A cracked bar in the refrigerator door

1 of 3 people found this instruction helpful.

Rochelle from Culver City, CA
Really Easy
Less than 15 mins

I snapped out the old cracked bar and snapped in the new one!

Was this helpful?

Retainer Bar bend

Rita from Owensboro, KY
Really Easy
Less than 15 mins

Removed the bent bar and the end clips. Attached the end clips to the new retainer bar and snapped into place on the refigerator door. Very easy.

Was this helpful?

end caps were broken

Danelle from Williston, VT
Really Easy
Less than 15 mins
Screw drivers

Purchased new ones. Took out the old ones with a screwdriver and slid the new ones in. Had to repair small section of the skin with glue and white duc tape where one of the end caps had ripped through

Was this helpful?

1993LPO General Electric Ice Maker - Instructions