1950LE Poulan Chainsaw - Parts

It is a genuine item that is supplied by the original manufacturer for use with Poulan and Weed Eater chainsaws. This washer-clutch is a special friction disk that helps to engage the clutch by ensuring a right fit between connected components. It provides an identical replacement for a damaged or a missing hardware that was installed on ...Read morea new unit. Check the diagrams of your model for the exact location and the correct installation of this part. One durable metal washer-clutch is included. You may need a screwdriver and a wrench set to perform this repair.

This is a genuine OEM sourced replacement part designed for use with chainsaws. It is made out of metal and it is sold individually. This is the part that fits over the bar and it is what cuts the material. Over time the chain will stretch and become dull so it will need to be replaced. To replace this chain you would need a wrench, scre...Read morewdriver and pliers. • Remove the buide bar side panel • Release the chain tension • Remove the old chain • Loosen the tensioning screw • Thread the new chain onto the saw • Align the guide bar • Replace the side plate • Tighten the chain to the correct tension • Finish tightening the side plate nuts

Genuine Poulan replacement part, this part is sold as a kit. The purpose of the 530071259 Oil Pump Kit is to keep the chain saw chain oiled, so it will not burn the teeth or get dull quicker than a well oiled chain would. It also contains complete installation instructions with it.

This is a genuine OEM sourced replacement part designed for use with Poulan chainsaws. The ignition module also known as armature-magneto provides current for the ignition system by producing pulses of high voltage for the spark plugs. It is made out of metal with some rubber components and it is sold individually. Includes a spark plug b...Read moreoot. To complete this repair you would need screwdriver set. Please note replacing this module would differ based on your unit, however the basic steps would be the same. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Install the red wire • Set the gap • Install the black wire • Reassembly and test the unit

This genuine replacement screw is a high-quality OEM part designed for use with Paramount and Poulan gas-powered lawn and garden equipment. It is specifically engineered to secure the starter rope within the pulley, ensuring reliable starting performance. Made from durable metal, this specialty screw is sold individually. Installation...Read more Tip: A flat-head screwdriver is required for removal and installation. For proper placement and application, please refer to your equipment’s model diagram.

This is a genuine part sourced directly from the manufacturer. The Washer-thrust is commonly found in Poulan, Husqvarna and Jonsered chainsaws. The washer is utilized to provide a tight fit between connected parts. It is a high-quality replacement for a damaged or a missing hardware that was installed on a new unit. Refer to the diagrams ...Read morefor your model to ensure the exact location and the correct application of this part. Keep in mind this washer is made of durable metal and is sold as an individual item.

This is a genuine OEM approved starter spring which is specially designed for use with handheld lawn and garden equipment. It is an identical replacement for a missing or a faulty component that was installed on a new unit. The purpose of this spring is to retract the starter assembly on the engine, so it engages the drive cup on the flyw...Read moreheel to start the engine when pulled. This high-quality spring is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams of your model for the correct location and application of this item.

This is an authentic replacement part sourced from original manufacturer. It is commonly used on gas chainsaws. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond ...Read morethe point of when they need to be replaced. Keeping an eye on equipment performance will determine when the centrifugal clutch requires attention. This clutch is made out of metal and it is sold individually. Please note the clutch drum, spacer and washer are all sold separately. To replace this item you would need a screwdriver and pliers.

This replacement part is an authentic OEM screw designed for use with gas chainsaws and trimmers. This item is generally used to secure the housing of the equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To secure or loosen this screw you would need a phillips head screwdriver.

This check valve, also known as a one-way valve, is a genuine OEM part that regulates the flow of fuel/oil in the equipment engine to prevent it from flowing backwards. It is made of plastic and designed for use in a variety of lawn and garden power equipment. If the valve is jammed, worn down, or contaminated with dirt and debris, it wil...Read morel be unable to open and close properly, thus restricting the flow of fuel and compromising the engine combustion process. You will likely notice fuel leaks around the carburetor, engine stalling, hard starting, and overall lower performance from your equipment. To remove the faulty valve, carefully disconnect any hoses or fasteners connected to it. Place the new valve in position and secure it appropriately.

This is an authentic OEM sourced part that is intended to be used with chainsaws from Poulan, Husqvarna, and Jonsered. Overtime ethanol in gasoline can deposit residue in the carburetor, and it can eventually become clogged and will cause engine performance issues. The kit includes the recommended parts to be replaced when cleaning and re-building a damaged carburetor.