18M33PCEH (P1214826R) Amana Air Conditioner - Instructions

It Went well Part was very fragile

Since the power and gas to the dryer were both already turned off all I had to was open the top of the dryer, remove the front panel, look underneath the drying drum and remove the belt tensioner from the belt and slide the drying drum out. While things were open I took my vacuum and vacuumed all the lint, dirt and loose articles from o ... Read more ver time out of the dryer interior. I located the igniter, used a nut driver to remove one screw pulled the igniter from its housing and disconnected the wiring harness. For installation I reversed the process and I was done. I reinstalled the drying drum, reattached the belt tensioner, put the front panel back in place and closed the dryer top. Attached the dryer vent hose, plugged the dryer to the electrical outlet, turned on the gas and walla it purred like a kitten. It even seem to dry faster than before.

Followed the easy instructions on the video, and it worked. Sure beats calling a technician.

Replaced igniter

First disconnect power to the machine. Remove lower access door locate the igniter connector and disconnect it. Now, remove the screw holding the igniter to the mounting bracket with a 5/16" box wrench, carefully remove the igniter. Replace the old mounting bracket but first start the igniter mounting screw in the new bracket, threadin ... Read more g it in all the way and then removing it to make installation easier. Install the new bracket and then the igniter, Be very careful, the igniter is fragile. Holding the igniter securely, install the mounting screw. Reconnect the wire connector replace lower door and plug the machine in. Voila! heat!!

Initially thought it was the thermal fuse since that has already been replaced twice before for the same type of problem. After replacing the fuse the same issue remained, so I did a little hunting on the internet and found some matrixes to help diagnose the issue. After a couple of minutes, I discovered it was the ignitor. I immediately ... Read more ordered the part and received it in about 5 business days. Even though that took longer than previous orders (usually < 3 days), I was still happy to get the part at a MUCH cheaper price than available locally. Installation took about 5 minutes with only a 5/16" nut driver and we were back in business. Kind of glad it broke because the dryer needed a good de-linting and cleaning anyway. : )

Removed back panel and tested all components. Everything was good so had to remove front to test last 2 components. Removed front and used brick (handy tool when your working solo) to hold drum up and in place (with full load of damp towels). Defective igniter. Testing all took 10 minutes, replacement took 2. Spent more time opening and p ... Read more utting machine back together than testing and replacement took.

Viewed online then found part and ordered it in, took front off of dryer and cleaned out the dryer. replaced igniter seemed to work but ended up having to replace thermial fuse.

Probably could have went faster but wasn't sure on how it would go. Overall not to bad. I wish the manufacturing companies would include the breakdown of the applicances like they use to,that would have helped alot. On the front panel there are 2 clips that you have to pay a lot of attention to. Otherwise you will break them off. . Gainin ... Read more g access to the igniter clip was somewhat of a chore but if you go slow it goes pretty good.

Just like the instructions. Piece of cake.

Initially confused by instructions provided in that it stated to loosen a brass coupler. Disconnected power. Removed front bottom panel. Disconnected both leads to ingiter. Removed the 2 screws holding igniter bracket in place. Carefully slid igniter and bracket forward and removed from dryer. Removed screw holding ingiter and replaced wi ... Read more th new. Reinstalled in reverse.

replaoed igniter ,easy to do after watching video

Viewed your video on line VERY HELPFUL, problem is the igniter will not stay on long enough to heat up. I just went back on your site and ordered a Thermal Fuse and a Cycling Thermostat for the machine but think it may be to old of a machine to keep trying to repair.

It took me nearly 3 hrs. but I don't do this for a living. Your instruction video was most helpful, madeit easy to know what to do & how to repair dryer. Part Select is top on my list. The site is easy to use & tells you what to replace based on the problem you are experiencing. The instinctual video are the best in the BUZ! Many thanks f ... Read more or making difficult repair much easier. David