My Orders
1893 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burner would not heat
27 of 35 people
found this instruction helpful.
-
Edward from Malvern, AR
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
First i shut off the power since this is an electric cook top/range. I then removed the knob and the two screws that hold the burner switch in place. I removed the wires one at a time and connected each to the new switch. I then reattached the screws to the switch. The most difficult part to me was breaking off the switch stem at the
... Read more
right level. I got that done and finally selected the appropriate adapter for the stem/knob fit.
Read less
Was this helpful?
Thank you for voting!
Purchased home but stove had no broiler pan.
16 of 33 people
found this instruction helpful.
-
Raymond from BLOOMINGTON, MN
- Very Easy
- Less than 15 mins
Purchased 2 piece broiler pan from this site
Was this helpful?
Thank you for voting!
burner quite heating discovered switch was the problem
9 of 12 people
found this instruction helpful.
-
Ronald from McClelland, IA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
lifted hood top unscrewed 4 small screws opening lid to switch housing took out 2 small screws that held the switch and then transfered wires to new switch replaced new switch with 2 new screws and back to working again walla! Time spent less than 30 minutes very simple as the instructions were very self explainatory.
Was this helpful?
Thank you for voting!
The switch had shorted
8 of 12 people
found this instruction helpful.
-
Stephen from COlleyville, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I reviewed the schematic. Removed the outer casing. Pulled out the existing wires and replaced them exactly on the new switch. Snipped out off the control stem to match the others. There was a small metal piece on the old stem which holds on the knob. I removed it from the old stem and put it on the new stem and Eureka.
Was this helpful?
Thank you for voting!
Dry rotted rubber
7 of 12 people
found this instruction helpful.
-
James from PICAYUNE, MS
- Very Easy
- Less than 15 mins
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Was this helpful?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
4 of 7 people
found this instruction helpful.
-
Alan from RADFORD, VA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
Read less
Was this helpful?
Thank you for voting!
faulty switch
2 of 2 people
found this instruction helpful.
-
James E from RIDGECREST, CA
- Really Easy
- 30 - 60 mins
I found the received switch (PS12070192) a poor replacement for the original, or even the earlier replaced part (PS11744446, in 2016) I was going to replace since the press/return feature seemed slow to return.
The male spade lugs on the received switch are so positioned that engagement is only possible if the lug is bent out ... Read more at a large angle. The lug set-back from the body edge, and the raised ribs on the sides still prevent full engagement of the connections.
I did install the new switch but found that was the only switch that didn’t give a signal light when turned on.
I have reinstalled the earlier unit.
Is part# PS 11744446 no longer available?
James E Weimholt. [email protected]
The male spade lugs on the received switch are so positioned that engagement is only possible if the lug is bent out ... Read more at a large angle. The lug set-back from the body edge, and the raised ribs on the sides still prevent full engagement of the connections.
I did install the new switch but found that was the only switch that didn’t give a signal light when turned on.
I have reinstalled the earlier unit.
Is part# PS 11744446 no longer available?
James E Weimholt. [email protected]
Read less
Was this helpful?
Thank you for voting!
Old infinity switch on electric rangetop did not work correctly
2 of 2 people
found this instruction helpful.
-
Decker from GREAT NECK, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Lifted range top, disconnected and labled wires from old switch, removed old switch, replaced wires on new switch, installed new switch.
NOTE: Local appliance store informed me that the electric cooktop was too old and that a replacement switch was not available and wanted to sell me a new cooktop for $795!
I found the switch ... Read more on PartSelect and repaired the cooktop. Total cost... UNDER THIRTY DOLLARS!!
NOTE: Local appliance store informed me that the electric cooktop was too old and that a replacement switch was not available and wanted to sell me a new cooktop for $795!
I found the switch ... Read more on PartSelect and repaired the cooktop. Total cost... UNDER THIRTY DOLLARS!!
Read less
Was this helpful?
Thank you for voting!
Surface Element switch faulty with no control on heat
1 person
found this instruction helpful.
-
Ramiro from AUSTIN, TX
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Turned power completely off. Removed knob from front panel. Opened range top cover. Removed 3 screws from aluminum panel protector behind the element switch. Once panel is removed you can see the switch element. Remove 2 screws from the front panel that connects to the element switch. Remove the old element and replace with new element ma
... Read more
king sure that each of the 5 wires on the old element is transferred one by one to the new element. Reverse the process in putting it all together. Turn on the power and walla you've have a new stove. You just save $600 plus.
Read less
Was this helpful?
Thank you for voting!
major gas leak on my generator
9 of 25 people
found this instruction helpful.
-
John from LEES SUMMIT, MO
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
popped out the old-----the bushing failed. replaced as per the included instructions
Was this helpful?
Thank you for voting!
broiler pan missing
1 of 2 people
found this instruction helpful.
-
RAYMOND from JACKSONVILLE, FL
- Really Easy
- Less than 15 mins
ordered new broiler pan
Was this helpful?
Thank you for voting!
Original burner switch fell apart
-
Jim from Addison, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Replacement was simple. Old switch was easily removed. Once I swapped the wires from old to new we were in business. One thing I would do differently than the included directions called for. I wish I had waited until I had installed the new switch to set the shaft length. I snapped off one too many sections of the shaft after measuring th
... Read more
e original shaft as recommended. If I had installed the replacement switch and then set the shaft length it would have been more accurate. Everything still works but one knob is now slightly lower than the other three.
Read less
Was this helpful?
Thank you for voting!
plastic post for knob broke off
-
Graham from Bridgeville, CA
- Really Easy
- Less than 15 mins
I broke the correct post from the new cluster of post selections and stuck it on. I had the kit for a couple of weeks before I realized that this was not an electrical problem. It would have been good of you to send only the new plastic post. That kit was intimidating for a 73 year old woman who lives in the country and does most of he
... Read more
r own plumbing and other household repairs. The repair took less that one minute.
Read less
Was this helpful?
Thank you for voting!