EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

1858 - Instructions

All Instructions for the 1858
76 - 90 of 599

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Leaking water pump
7 of 13 people found this instruction helpful.
  • John from Palatine, IL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.
Was this helpful?
Thank you for voting!
Thanks for sending the correct part. You guys did a great job.
4 of 4 people found this instruction helpful.
  • Albert from Dallas, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set, Wrench set
Just put the part on.
Was this helpful?
Thank you for voting!
the sump housing was worn out and leaked
4 of 4 people found this instruction helpful.
  • sandra from colorado springs, CO
  • Easy
  • 15 - 30 mins
  • Screw drivers
first I used a shop vac to clean any excess water left behind, removed the sump housing from the motor, removed the sump housing from the body of dishwasher, replaced the old housing for the new one and reversed my steps to remove old one,
Was this helpful?
Thank you for voting!
Upper rack kept dropping from the wheels when we pulled it out
4 of 4 people found this instruction helpful.
  • Joel from Cypress, TX
  • Easy
  • Less than 15 mins
We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, w hich made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.
Was this helpful?
Thank you for voting!
Missing wheels
4 of 4 people found this instruction helpful.
  • Felix A from Orlando, FL
  • Really Easy
  • Less than 15 mins
Inserted wheels on socket and then into the dishwasher rack.
Was this helpful?
Thank you for voting!
Dispenser cap would not stay in place because it had melted
5 of 7 people found this instruction helpful.
  • Patricia from Clifton, NJ
  • Really Easy
  • Less than 15 mins
First I opened the package and screwed the new dispenser cap into place.
Was this helpful?
Thank you for voting!
rack slide end cap missing
4 of 4 people found this instruction helpful.
  • Carrell from Cochranville, PA
  • Really Easy
  • Less than 15 mins
installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy
Was this helpful?
Thank you for voting!
Three of the 8 wheels broke.
5 of 7 people found this instruction helpful.
  • Asok from HELOTES, TX
  • Very Easy
  • Less than 15 mins
The newly purchased wheels have a little different design and could be installed in a matter of few seconds.
Was this helpful?
Thank you for voting!
dishwasher did not start
7 of 13 people found this instruction helpful.
  • Lawrence from ROLESVILLE, NC
  • Very Easy
  • Less than 15 mins
Took out interlock switch (two leads) and replaced with new one. As simple as that.
Was this helpful?
Thank you for voting!
Wheel had melted and support cracked
5 of 7 people found this instruction helpful.
  • Tom from UPPR CHICHSTR, PA
  • Very Easy
  • Less than 15 mins
Removed the lower rack and installed new wheels with clips
Was this helpful?
Thank you for voting!
spray arm falls off
5 of 7 people found this instruction helpful.
  • JAMES from AUBURN, WA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Turn off power at breaker box.
Remove lower covers and 2 screws into counter top.
Verify sufficient length on water and electrical connection to allow sliding dishwasher out approx. 2/3. I disconnected the electrical at the j box on the dishwasher. If you must disconnect the water line, shut off supply, usually located under nea rby sink, and provide a rag or sponge for small amounts of water left in supply line.
Carefully pull back the insulation to expose two screws on top where water line runs into the center.
Pull the top tray part way out and reach in to hold the spray arm while removing the screws. The spray arm will easily drop out.
Hold the new spray arm in place making sure the raised screw posts push into the holes, then reinstall the two screws. Done. Pull insulation back into place, retape if necessary. Reconnect electrical and water if necessary.
Slide unit back in, checking alinement. Rescrew to counter top and reinstall lower covers. Task complete. 15 mins if prepared. 30 mins if both elect. & water are disconnected and you are somewhat hesitant.
Was this helpful?
Thank you for voting!
Motor froze up on dishwasher
5 of 8 people found this instruction helpful.
  • Raymond from Oshkosh, WI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfie d.
Was this helpful?
Thank you for voting!
Silverware basket was missing in the condo that we rented
4 of 5 people found this instruction helpful.
  • donald from fullerton, CA
  • Really Easy
  • Less than 15 mins
I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket. ... Read more />I was very happy the the service.
Donald Brown
Was this helpful?
Thank you for voting!
Rinse Aid Fill Cap melted because it landed next to the heating element because it wasn't screwed in
4 of 5 people found this instruction helpful.
  • Helen from Carol Stream, IL
  • Really Easy
  • Less than 15 mins
Simply screwed in new cap
Was this helpful?
Thank you for voting!
poor dish washing
4 of 5 people found this instruction helpful.
  • THOMAS from LACONIA, NH
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.
Was this helpful?
Thank you for voting!
All Instructions for the 1858
76 - 90 of 599