1807 - Overview

This is a genuine OEM sourced component which is specially designed for Craftsman pressure washers. It is an identical replacement for a missing or damaged outlet that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this item. Keep in mind this high-quality part is made of durable metal and is sold individually.

This OEM Carburetor Bowl Gasket attaches between the carburetor bowl and carburetor in order to seal the parts together. This model is rubber, black, and comes individually sold. Installation is rated as "Easy" by customers, and will require pliers and a socket set. If the part becomes broken due to wear/damage then there may be a fuel le...Read moreak, and the part will need to be replaced. Refer to your make, model and diagrams to ensure you've chosen the correct part.

Sourced directly from the manufacturer, this part is used to open and release hot water if the water exceeds the maximum operating temperature. It has metal and plastic components, is not part of a kit or assembly, and is sold individually. When malfunctioning, the Thermo Relief Valve will open on a regular basis, which can cause damage ...Read moreto your pump. If it is opening often or on a regular basis, replace it to protect your pump from damage. You will need a socket set, a wrench set, and pliers to complete this repair. Customers rate this repair as Easy.

Sold as a kit including the connector, ball, and spring, this genuine OEM replacement part is used in various models of pressure washers to connect the chemical hose (soap hose) with the pump. It will be found on the pump of your machine and is made of metal. You will know this part is malfunctioning if you do not have soap coming out o...Read moref the nozzle. This part is known to wear over time and should be replaced when you noticed signs of damage or fatigue. You will need a wrench set to complete this repair. Customers rate this repair as Easy.

This is the lower handle for various models of walk-behind lawn mowers. This handle is made of durable black metal and attaches directly to the rear of the lawn mower. This handle is an OEM part that is sold by itself and does not come with any hardware or other parts. If your current lower lawn mower handle is corroded or damaged, it nee...Read moreds to be replaced immediately so you can properly and safely handle your lawn mower. This handle measures approximately 24.5-inches long and 17-inches wide and connects the rear of the lawn mower with the upper and main handle that the user holds when operating the lawn mower. Replacing this handle will not require any tools but must start with turning off the lawn mower. Loosen and remove the knobs around the handle, including the ones connecting the lower handle to the mower and those securing the upper and lower handles. Once each knob is removed, replace the old lower handle with the new one, and resecure • all the knobs onto the handle(s).

Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between various part assemblies along a shaft. If you hear a strange noise coming from the shaft area, or you notice the Washer is visibly worn or damag...Read moreed, it will need to be replaced. Refer to your owners manual to determine the exact location of this part. Customers rate the difficulty of this repair as Medium.

The Fuel Line Clamp is a metal, individually sold part which clamps onto the fuel line, securing it to a port and preventing leaks. Installation is rated as "Easy" by customers and will require pliers and a screwdriver. If broken due to wear/fatigue/damage, there may be a fuel leak and the part should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.

This Washer-Lock 5/16 is a silver metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter it is used to prevent the nut from backing off and becoming loose on the pulley shaft and is attached to the drive belt pulley assembly. You will know if you need t...Read morehis because your owners manual will specify it or the model number of your machine will correspond with this part. If the part is broken due to fatigue the shafts will free spin when they should be locked together and must be replaced.

Designed for use in various models of pressure washers, air compressors, and generators, this Woodruff Key is used to hold a shaft with a mating part, such as a gear. It is 1 inch in length, made of metal, is silver, and is sold individually. If the mating shaft or gear no longer rotates together, you likely need to replace the Woodruff...Read more Key. Inspect it for signs of fatigue or wear, which occurs through regular use, and replace it if needed. You will need a wrench set, an allen key set, a screwdriver, and pliers to complete this repair. Customers rate this repair as Easy.

This item is an authentic OEM sourced O-ring kit that replaces worn or damaged O-rings for the gun, hose and wand.Unfortunately, over time o-rings will wear out and they may begin to crack eventually requiring replacements. Refer to the appropriate diagrams for your model to ensure the correct replacement procedure. A screwdriver and a wr...Read moreench set might be needed to take apart and reassemble the equipment. Note, this kit is sold as an individual item.

This bottle of oil is OEM and approved by the manufacturer. It is compatible with dozens of models of pressure washers. This one 4.6 oz bottle is the adequate amount of oil needed for the machine. A socket set is required to remove the plug on the oil pump. It is recommended to use a small funnel to pour the oil into the pump to prevent spillage.

It is a genuine OEM sourced item that is designed for Briggs and Stratton, Snapper and Troy-Built pressure washers. The manifold housing is an important component that attaches to the pump head. It houses the unloader valve, the check valves, the outlet tube and the chemical injection assembly. If the manifold housing is worn or damaged i...Read moret can cause water leaks and it should be replaced to ensure the equipment is functioning properly. To determine the exact location and the correct installation of this manifold housing, refer to the appropriate diagrams of your model. You will need a screwdriver and a wrench set to perform this repair. This high-quality manifold housing is made of durable metal and is sold as an individual component.