1677-0 Briggs and Stratton Generator - Parts

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

This OEM replacement fuel gauge cap is designed for use in generators. It comes in a cylindrical shape and has a built-in window to easily view the fuel levels without pulling out the entire cap. It is approximately 5.25 inches in length, while the head has a diameter of 3 inches. The purpose of the cap is to cover and protect the fuel ga...Read moreuge, which indicates the levels of gas available in the tank. It prevents dirt and debris from entering the gauge area and prevents fuel from leaking out. A faulty cap will allow contaminants to enter the gauge, and cause fuel to leak, leading to inaccurate fuel readings and safety risks. Twist the cap to remove it and clean the surrounding area thoroughly. Place the new gauge cap in position and ensure that it is locked in place.

The hair pin is a silver, metal pin used to secure and lock parts in place. If broken, the part being secured will come loose and the pin should be replaced. This is an OEM part directly from the manufacturer. Most customers rated the replacement of the hair pin as an easy repair.

This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the electricity flow when it detects excessive current. It can handle a maximum current of 20 amps. You can tell if a circuit breaker is broken by c...Read morehecking for visible signs of damage, such as an unresponsive button, cracks, or burnt marks. If the circuit breaker repeatedly trips, the breaker may be faulty or overloaded. You will need a screwdriver, a set of pliers, a socket set, and a nutdriver to replace the breaker in your generator. Follow the instructions in your user manual to access the control box. You typically need to remove the carburetor and the fuel tank before removing the cover of the control box. Please note that this OEM replacement part is sold individually.

This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replace...Read morement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove the cover and gain access to the brush assembly • Take our old brushes and replace them with the new ones • Reassembly the cover

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

This is an authentic OEM part from Briggs and Stratton and Snapper for use with Generators. The fuel tank mounting grommet forms a cushion between the fuel tank and the fuel tank mounting bolts. The most common reasons for replacing the grommet is if the fuel is leaking from the fuel tank, the fuel lines are loose at the tank or the rubbe...Read morer grommet is cracked and not sealing. This part is made out of rubber and is sold individually. Here is a list of tools that are needed to replace the grommet a receptacle for draining fuel, a wire hook (to retrieve fuel lines), screwdriver, wire cutters or scissors.

The authentic 10" Wheel Assembly (Wheel, 10" Diameter) is a 10-inch black, plastic-and-ubber wheel. It allows easy moving of the generator. Installation requires pliers and is rated as "Easy". If your tire is flat, then it should be replaced. Refer to your make, model and diagram to ensure this is the right part.

This authentic OEM supplied trigger-throttle is designed for Briggs and Stratton and Snapper generators. It is designed to provide a user with a comfortable grip to operate the unit. This is an identical replacement for a damaged or a missing component that was installed on a new unit. Refer to the appropriate diagrams for your model to e...Read morensure the correct repair procedure. Keep in mind this high-quality handle assembly is made of durable material and is sold individually.

This is a genuine replacement part sourced from the original manufacturer for use with small engines. The special gasket is commonly used to seal the connection between the exhaust manifold and the cylinder head. This special gasket is available as an individual replacement part, please see model diagram for associative parts.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.