My Orders
1669 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dry rotted rubber
7 of 12 people
found this instruction helpful.
-
James from PICAYUNE, MS
- Very Easy
- Less than 15 mins
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Was this helpful?
Thank you for voting!
remove and replace
10 of 24 people
found this instruction helpful.
-
Perry from Flushing, NY
- Really Easy
- Less than 15 mins
very easy remove the bad bulb install the new one
Was this helpful?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
4 of 7 people
found this instruction helpful.
-
Alan from RADFORD, VA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
Read less
Was this helpful?
Thank you for voting!
major gas leak on my generator
9 of 25 people
found this instruction helpful.
-
John from LEES SUMMIT, MO
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
popped out the old-----the bushing failed. replaced as per the included instructions
Was this helpful?
Thank you for voting!
Fluorescent lamp bulb
1 person
found this instruction helpful.
-
Danial from HILLSBORO, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrew the metal rim and remove the glass window. Remove the old bulb by twesting the bulb towards you. Place the new bulb's pins into the slots and twest away from you. Place the metal rims back in place and screw them down.
Was this helpful?
Thank you for voting!
dropped & broke the oven light bulb cover
1 of 2 people
found this instruction helpful.
-
joseph from san jose, CA
- Really Easy
- Less than 15 mins
popped the new one on!
Was this helpful?
Thank you for voting!
Had generator repaired and the lost the handle
1 of 3 people
found this instruction helpful.
-
Melinda from Port Saint Lucie, FL
- Really Easy
- 15 - 30 mins
-
Socket set
Removed the old bracket from the generator and installed new bracket and handle using the same bolts.
Was this helpful?
Thank you for voting!
Solenoid failed due to excessive heat.
0 of 1 people
found this instruction helpful.
-
Joseph from Martins Creek, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed back panel. Removed the defective solenoid on its bracket. Replaced it with the new door latch solenoid. This was relatively easy. Replaced the back panel. Tested self cleaning feature. Everything worked fine. I have preformed this same repair once before.
Was this helpful?
Thank you for voting!
Convex element burned out
-
John from Eden prairie, MN
- Easy
- 30 - 60 mins
-
Socket set
REmoved the covers, removed the old part, be careful with the electrical connections, they move back behind the wall and are hard to get back in the open. While waiting for the new part, 2 days, I cleaned the oven. Works like new.
Was this helpful?
Thank you for voting!