1669-0 Briggs and Stratton Generator - Parts

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

The hair pin is a silver, metal pin used to secure and lock parts in place. If broken, the part being secured will come loose and the pin should be replaced. This is an OEM part directly from the manufacturer. Most customers rated the replacement of the hair pin as an easy repair.

This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the electricity flow when it detects excessive current. It can handle a maximum current of 20 amps. You can tell if a circuit breaker is broken by c...Read morehecking for visible signs of damage, such as an unresponsive button, cracks, or burnt marks. If the circuit breaker repeatedly trips, the breaker may be faulty or overloaded. You will need a screwdriver, a set of pliers, a socket set, and a nutdriver to replace the breaker in your generator. Follow the instructions in your user manual to access the control box. You typically need to remove the carburetor and the fuel tank before removing the cover of the control box. Please note that this OEM replacement part is sold individually.

This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replace...Read morement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove the cover and gain access to the brush assembly • Take our old brushes and replace them with the new ones • Reassembly the cover

This is a genuine manufacturer-sourced replacement wheel which is specially designed for use with Briggs and Stratton and Snapper generators. It is an identical replacement for a missing or damaged wheel which supports the unit and allows for easy transportation. This is a high-quality component which is made of durable plastic and is sold individually, please note the hardware to secure it is sold separately.

This authentic OEM supplied trigger-throttle is designed for Briggs and Stratton and Snapper generators. It is designed to provide a user with a comfortable grip to operate the unit. This is an identical replacement for a damaged or a missing component that was installed on a new unit. Refer to the appropriate diagrams for your model to e...Read morensure the correct repair procedure. Keep in mind this high-quality handle assembly is made of durable material and is sold individually.

This is a genuine replacement part sourced from the original manufacturer for use with small engines. The special gasket is commonly used to seal the connection between the exhaust manifold and the cylinder head. This special gasket is available as an individual replacement part, please see model diagram for associative parts.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or damaged, the nut and part may be loose and it should be replaced. Check your make, model and diagram to ensure you are choosing the correct part.

This item is available as an individual replacement part. The outlet is made out of metal and plastic. It may require a wrench during installation. This item will need to be replaced if it breaks. It is a replacement part directly sourced from the manufacturer for use in generators made by Briggs & Stratton and Snapper.