Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The bottom strip had become rusty and looking badly
5 of 9 peoplefound this instruction helpful.
Carolyn from North Port, FL
Easy
15 - 30 mins
Nutdriver
I pulled the oven door off the hinges and took the bolts out of the bottom of the over that were holding the strip on. I then pulled the strip off and replaced it with the new on. I replaced the bolts and then replaced the door on the hinges.
Was this helpful?
Thank you for voting!
remove and replace
10 of 24 peoplefound this instruction helpful.
Perry from Flushing, NY
Really Easy
Less than 15 mins
very easy remove the bad bulb install the new one
Was this helpful?
Thank you for voting!
Oven door handle broke
3 of 4 peoplefound this instruction helpful.
William from Bartlett, TN
Easy
15 - 30 mins
Pliers, Screw drivers
Had to take back off of the door to get to screw that held the broken piece of handle before installing the new part. Then had to put the back on the door and slip the door into place.
Was this helpful?
Thank you for voting!
bottom trim had rusted, so we needed new piece
3 of 4 peoplefound this instruction helpful.
Robin from Apple Valley, MN
Really Easy
Less than 15 mins
Socket set
Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked op
... Read moreen!)
Read less
Was this helpful?
Thank you for voting!
aged burner bowls
3 of 4 peoplefound this instruction helpful.
Louis from Sandwich, MA
Really Easy
Less than 15 mins
I just removed the range elements and old bowls, placed the new bowls into the range top, and inserted the heating elements. What surprised me was the quickness in filling the order. I had the new parts the next day! Great!
I unplugged the burner, lifted the old drip pan out, put new drip pan in, plugged burner in. The stove looks brand new and it took less than 2 minutes.
Your support team helped tremendously in ordering the parts. Parts arrived in only 2 days. Upon taking the door off the oven we had to remove several screws, then more screws. Was able to take it almost fully apart, replace old broken parts with new. Putting it back together was like a puzzle. We did it though and saved money! Thanks
old valve dripped gas when opened on cold sub zero day
4 of 7 peoplefound this instruction helpful.
Alan from RADFORD, VA
A Bit Difficult
1- 2 hours
Pliers, Screw drivers
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read morer /> used same technique to insert valve upward into bushing
works great!
Read less
Was this helpful?
Thank you for voting!
the old screws were not correct so it took 1/2 hour for me to find screws that would. there should have been proper screws sent with the end cap.
2 of 2 peoplefound this instruction helpful.
anthony from Jacksonville, FL
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
I attached the end caps to my existing handle, but had to squeeze the parts together very hard to get them to mesh to the correct distance of the holes. I removed the screws holding outside frame of the oven door. I then opened the door fully, propping it up on my knee and removed the inside end cap screws. Placing the handle in positi
... Read moreon underneath the propped door, I attached the screws. Lastly I reassembled the door.
Read less
Was this helpful?
Thank you for voting!
door handle and end caps broke
2 of 2 peoplefound this instruction helpful.
Jack from BARTLETT, TN
Very Difficult
More than 2 hours
parts need to be delivered to do repair, its been over a month. customer service is not taking calls. I have paid for parts I did not receive.
Was this helpful?
Thank you for voting!
just needed new GE burner bowls
2 of 2 peoplefound this instruction helpful.
Jacqueline from E WENATCHEE, WA
Very Easy
Less than 15 mins
Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.
Bottom trim piece on 24 year old stove had rusted. Replace trim piece was still available.
2 of 2 peoplefound this instruction helpful.
Donald from FAYETTEVILLE, NY
Very Easy
Less than 15 mins
Socket set
Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim. Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.
Was this helpful?
Thank you for voting!
Part rusted over time...22 years.
2 of 2 peoplefound this instruction helpful.
Jeannene from HUNTINGTON, TX
Very Easy
Less than 15 mins
Screw drivers
Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.
Was this helpful?
Thank you for voting!
Replace door gasket on very old wall oven
2 of 2 peoplefound this instruction helpful.
r from SUNNYVALE, CA
Easy
15 - 30 mins
Nutdriver, Screw drivers
Repair went a lot faster and easier than I anticipated. Instructions are similar to those posted by others. 1. Verify that new gasket looks mostly like old gasket as best you can since not all of old gasket is visible. 2. Shut off circuit to oven (optional, but good practice) 3. Remove racks, trays, etc from oven to red
... Read moreuce weight at Step 7 4. Remove oven door by partially opening door to broiler position (about 20 degrees). Door should catch and stay open on its own. Slide up and lift off door. The “hinges” are spring loaded so carefully return them to closed position so they won’t snap shut on fingers. 5. Remove Phillips screws, one on each side wall of oven liner. 6. Remove two hex screws and metal gasket-holder on top center of oven liner. 7. Pull and slide oven liner out of oven mainframe about 1/4 “ to 3/8”. This may be the most difficult part of the job. 8. If possible to remove just a couple of inches of one bottom of old gasket (right side is easiest), verify that the cross-section profile of both old and new gaskets are essentially the same. If not, you have the wrong gasket. 9. Pull and remove old gasket. If gasket is dry and cracking, it may be necessary to scrape it out with putty knife, flat-blade screwdriver, etc. if it has fused to metal over the years. Note how it was installed on the metal edge of the oven liner. 10. Locate the mid-point on the new gasket length and begin inserting it at the top-center of the oven liner where you removed the two hex screws. Continue installing along both left and right sides of the liner. Each end of the gasket should extend to just above the respective hinge. No trimming should be necessary. Ensure a snug fit all along each side and top. 11. Push liner back into oven mainframe. Replace Phillips screws, gasket-holder, and hex screws. 11. Pull out each hinge to broiler position. 12. Replace door by sliding down onto hinges. Close door and check for tight fit against gaskets. Gaskets will flatten somewhat over time 13. Restore power, racks, trays, etc.
Read less
Was this helpful?
Thank you for voting!
Stove was not getting enough power.
2 of 2 peoplefound this instruction helpful.
Nathan from Wells, ME
A Bit Difficult
15 - 30 mins
Nutdriver, Pliers, Screw drivers, Socket set
My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),r
... Read moreed] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.
My Orders
