150212 Briggs and Stratton Engine - Parts

This item is available as an individual replacement part but also includes the screws. The muffler deflector attaches to the lo-tone muffler and is made of metal. A nutdriver might be required during the replacement of this item. It may become broken and will need to be replaced. This is an authentic Briggs & Stratton and Toro replacement...Read more part that is sourced from the original manufacturer for use with engines, snowthrowers, tillers, lawn mowers, and lawn tractors.

A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other ...Read moresmall engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.

This is a genuine OEM supplied replacement part designed for use with Briggs and Stratton engines. This float controls fuel flow into the carburetor bowl by adjusting the needle valve. Includes a plastic float and a metal pin. To complete this repair you would need a wrench and pliers.

This spark plug is an authentic OEM replacement part, it is not an aftermarket equivalent. It is specially made for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. A spark plug helps to deliver electric current from an ignition system to the combustion chamber. Please note, this item is sold indi...Read morevidually. You should always gap the spark plug in accordance with the owners manual of the outdoor product you have. Replacing a spark plug you will need a apark plug wrench or a socket wrench to get the job done.

This is an authentic OEM sourced replacement part that is intended to be used with lawnmower engines and outboard motors from Briggs & Stratton and Toro. The metal screw is used to secure the rocker cover to the cylinder head assembly. This item is available as an individual replacement part.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This replacement screw is generally used to secure the muffler guard, for correct application make sure to check appropriate diagrams of your model. It is a high-quality Torx screw which is sold individually.

The exhaust gasket attaches to the exhaust manifold and helps to form a seal. It is an authentic OEM sourced part which is specially designed for use with Briggs & Stratton generators and engines, plus Toro snowthrowers and lawn tractors. This gasket is made of a flexible material and is priced individually. A screwdriver and a wrench may be needed to install this part.

This authentic OEM sealing washer is designed for your lawn equipment to create a tight seal within the carburetor body, preventing fuel or air leaks. If you notice any signs of leaks, such as dripping fuel or hissing sounds, it may indicate a faulty or worn-out sealing washer. Additionally, you might be experiencing engine performance is...Read moresues like rough idling or difficulty starting. To replace the sealing washer, ensure that the machine is off and that the engine has cooled down. Remove the air breather cover and the filter itself, following the instructions provided in your user manual to access the carburetor. Depending on your specific equipment model, you may need to detach the springs from the carburetor choke mechanism, disconnect the fuel line and fuel tank, remove the choke lever, and detach the air breather base. Once you have located the carburetor, carefully unthread the main jet from the bottom of the carburetor bowl. Finally, slide off the old sealing washer, ensuring you take note of its positioning for accurate replacement. Please note that this sealing washer is sold individually.

This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to transfer vacuum from the engine. Unfortunately, over time the material may wear out and begin to crack eventually ...Read morerequiring a replacement. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. Note, this item includes one durable rubber hose and two metal clamps to secure it.

This item is a genuine replacement part that has been OEM sourced and is intended to be used with lawnmower engines from Briggs & Stratton and Toro. The rubber seal is used to prevent oil from leaking at the connection between the bottom of the oil fill tube and the crankcase. This item also allows the fill tube to firmly sit into the case. The dipstick tube seal if available as an individual replacement part.

Introducing the Starter-Rewind from Briggs and Stratton, tailored to ensure your engine starts up reliably every time. This component is designed for durability and strength, promising to endure rigorous use with ease. As a crucial part of your engine's ignition system, the Starter-Rewind delivers consistent performance. It's engineered t...Read moreo Briggs and Stratton's exacting standards, meaning it's designed for optimum compatibility and functionality. Experience the superior quality and reliability that Briggs and Stratton products are known for with their Starter-Rewind.

This is a genuine manufacturer-sourced part which is designed for use on lawn and garden equipment. It is an identical replacement for a missing or a damaged clamp that is used to secure the hose. Keep in mind this high-quality product is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams for your model for the correct location and application of this hardware.